manualshive.com logo in svg

Heat & Glo 8000TV-OAK, Руководство пользователя, Страница: 30 / 46

Поделиться
Скачать
Heat & Glo 8000TV-OAK Скачать руководство пользователя страница 30

30

Heat & Glo  •  8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI  •  2058-900  Rev. L  •  08/08

Before operating this appliance have a qualified 
technician:

•  Remove all shipping materials from inside and/or 

underneath the fi rebox.

•  Review proper placement of logs, rockwool, lava rock, 

and vermiculite.

•  Check the wiring.

•  Check the air shutter adjustment.

•  Ensure that there are no gas leaks.

•  Ensure that the glass is sealed and in the proper 

position.

•  Ensure that the fl ow of combustion and ventilation air is 

not obstructed (front grilles and vent caps).

Glass door must be in place when 
appliance is operating. Risk of:

• Combustion Fumes
• Fire

Do NOT operate appliance with glass door removed. 

•  Open viewing glass for servicing only.

•  Glass door MUST be in place and sealed before operating 

appliance.

•  Only use glass door certifi ed for use with appliance.

•  Glass replacement should be done by qualified 

technician.

FLAME UP

- ACCEPTABLE -

FLAME IN

- GOOD -

FLAME OUT

- BAD -

DRAFT HOOD

B. Check Appliance Draft

Figure  13.1

Check draft of appliance to 
verify proper venting condi-
tions.

•  Close all windows and 

doors, turn on all exhaust 
fans in home.

•  Appliance is to be com-

pletely assembled to nor-
mal operating condition.

•  Turn on appliance and al-

low to operate for at least 
10 minutes.

•  Check draft as shown in 

Figure 13.1. This can be 
done using a smoke or 
fl ame producing match.

•  Hold lit match at bottom 

edge of draft hood opening 
and observe fl ame/smoke 
per the fi gure.

A. Before Lighting Appliance

Before lighting this appliance determine if it has a Stand-
ing Pilot or Intellifi re ignition system by opening the con-
trol access panel to view wiring system and gas valve. If 
this appliance has a red or black ignitor button (see Figure 
10.1) this appliance has a Standing Pilot ignition system. 
If there is no red or black ignitor button, this appliance has 
an Intellifi re ignition system.

13 

13 

Operating Instructions 

 

 CAUTION

If installing Intellifi re ignition battery backup:

•  Do not install batteries if the backup mode may not be 

used for extended time.

•   Batteries may leak.

•   Install batteries only when needed for power outage.

Improper installation, adjustment, alteration, service or 
maintenance can cause injury or property damage. Refer to 
the owner’s information manual provided with this appliance. 
For assistance or additional information consult a qualifi ed 
installer, service agency or the gas supplier.

Do NOT use this appliance if any part has been under water.  
Immediately call a qualifi ed service technician to inspect the 
appliance and to replace any part of the control system and 
any gas control which has been under water.

WARNING

WARNING

WARNING

WARNING

This appliance has been supplied with an integral barrier 
to prevent direct contact with the fi xed glass panel. Do 
NOT operate the appliance with the barrier removed. 

Contact your dealer or Hearth & Home Technologies if the 
barrier is not present or help is needed to properly install one.

HOT SURFACES

! 

Glass and other surfaces are hot during 
operation AND cool down.

Hot glass will cause burns.

•  Do not touch glass until it is cooled
•  NEVER allow children to touch glass
• Keep children away

•  CAREFULLY SUPERVISE children in same room as 

fi replace.

•  Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other 
fl ammable materials.

•  Keep clothing, furniture, draperies and other fl ammable 

materials away.

Содержание 8000TV-OAK















































Отзывы:

Нет отзывов