manualshive.com logo in svg

Heat & Glo 8000TRC, Руководство по установке, Страница: 6 / 48

Поделиться
Скачать
Heat & Glo 8000TRC Скачать руководство пользователя страница 6

3

Figure 1. Diagram of the 8000TRC

The Heat-N-Glo Warranty will be voided by, and Heat-N-Glo disclaims any

responsibility for, the following actions:

• Installation of any damaged fireplace or vent system component.

• Modification of the fireplace or direct vent system.

• Installation other than as instructed by Heat-N-Glo.

• Improper positioning of the gas logs or the glass door.

• Installation and/or use of any component part not manufactured and approved by

Heat-N-Glo, not withstanding any independent testing laboratory or other party

approval of such component part or accessory.

ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARD.

When planning a fireplace installation, it’s necessary to determine:

•

Where the unit is to be installed.

•

The vent system configuration to be used.

•

Gas supply piping.

•

Electrical wiring.

•

Framing and finishing details.

•

Whether optional accessories—devices such as a fan, wall switch, or remote

control—are desired.

If the fireplace is to be installed on carpeting or tile, or on any combustible

material other than wood flooring, the fireplace should be installed on a metal or

wood panel that extends the full width and depth of the fireplace.

Содержание 8000TRC

















































Отзывы:

Нет отзывов