manualshive.com logo in svg

Heat & Glo 6000CBV-IPI, Руководство пользователя

Поделиться
Скачать
Heat & Glo 6000CBV-IPI Скачать руководство пользователя страница 29

Heat & Glo  •  6000CBV-IPI, 8000CBV-IPI  •  2167-900 Rev. C  •  9/09

29

A. Wiring Requirements

NOTICE:  This appliance must be electrically wired 
and grounded in accordance with local codes or, in the 
absence of local codes, with National Electric Code 
ANSI/NFPA 70-latest edition or the Canadian Electric 
Code CSA C22.1.

•  Wire the appliance junction box to 110-120 VAC. This is 

required for proper operation of the appliance ( IntelliFire 
Plus™ ignition).

•  A 110-120 VAC circuit for this product must be protected 

with ground-fault circuit-interrupter protection, in compli-
ance with the applicable electrical codes, when it is installed 
in locations such as in bathrooms or near sinks.

•  Low voltage and 110 VAC voltage cannot be shared 

within the same wall box.

WARNING! Risk of Shock or Explosion! DO NOT wire 
110V to the valve or to the appliance wall switch. Incorrect 
wiring will damage controls.

B.   IntelliFire Plus™ Ignition System Wiring

•  Wire the appliance junction box to 110 VAC for proper 

operation of the appliance.

WARNING! Risk of Shock or Explosion! DO NOT wire 
IPI controlled appliance junction box to a switched circuit. 
Incorrect wiring will override IPI safety lockout.

•  Refer to Figure 12.1,  IntelliFire Plus™ Pilot Ignition (IPI) 

Wiring Diagram.

•  This appliance is equipped with an  IntelliFire Plus™ 

control valve which operates on a 6 volt system.

•  Plug the 6 volt transformer plug into the appliance junction 

box to supply power to the unit OR install four AA cell 
batteries (not included) into the battery pack before use.

C. Optional Accessories Requirements

•  This appliance may be used with a wall switch, wall 

mounted thermostat and/or a remote control.

Wiring for optional Hearth & Home Technologies approved 
accessories should be done now to avoid reconstruction. 
Follow instructions that come with those accessories.

•  Use only IntelliFire Plus™ Wireless Controls or WSK-

21 wired wall switch with the IntelliFire Plus™ Ignition 
System. 

•  A standard ON/OFF switch is compatible.

12 

12 

Electrical Information 

 

f i r e - p a r t s . c o m

Содержание 6000CBV-IPI



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды