HearthStone Green Mountain Insert 70 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 43

background image

Hearthstone Quality Home Heating Products, Inc

® Green Mountain Insert 70 (Model 8450)

17

possibility of obstruction by snow, leaves or other
material.

Install the Outside Air Supply:

Using  pliers,  remove  the  rectangular  knock-out
plate  (A)  located  on  the  left  or  right  side  of  the
convection  air  jacket.    Choose  the  side  that is  best
for your installation.

Note: Only remove the knock-out that will be
connected to the fresh air inlet.

Figure 9

– Outside Air Inlet

Figure 10

– Outside Air Kit Detail

Then, install the fresh air kit adapter (B) using 4
screws (C). Secure the flexible pipe

1

(E) to the

adapter (B) using one of the adjustable pipe clamps
(D). Secure the other end of the pipe to the outside
wall termination (F) using the second adjustable
pipe clamp (D). The outside wall termination (F)
must be installed outside of the building.

1

The pipe must be HVAC type, insulated, and must

comply with ULC S110 and/or UL 181, Class 0 or
Class 1.

«
...
15
16
17
18
19
...
»

Содержание Green Mountain Insert 70












































Отзывы:

Нет отзывов

Похожие инструкции для Green Mountain Insert 70

Southern Series

Бренд: Warmington Страницы: 2

Бренд: Quadra-Fire Страницы: 36

Бренд: Quadra-Fire Страницы: 56

Бренд: Empire Comfort Systems Страницы: 8

Бренд: Napoleon Страницы: 4

Бренд: Everwarm Страницы: 25

Бренд: Calflame Страницы: 35

Бренд: BIGHORN Страницы: 18

Бренд: Majestic Страницы: 36

Бренд: ARTE Страницы: 30

Бренд: Valcourt Страницы: 6

Jensen Geneva 1581LP

Бренд: KSP Страницы: 51

Бренд: Heatilator Страницы: 73

Бренд: GlammFire Страницы: 12

Squaw Valley L-FT629PST

Бренд: Sunjoy Страницы: 4

L-FT253PST-6A-1

Бренд: Sunjoy Страницы: 6

Бренд: Sunjoy Страницы: 7

Бренд: Westfire Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды