Hearth and Home Technologies PVLP-SLP Скачать руководство пользователя страница 10

Страница: 10 / 33

Hearth & Home Technologies • Power Vent Low Profile (PVLP-SLP) Instructions • 4052-900 Rev. M• 09/17

A. Framing and Clearances

Chassis Dimensions

The dimensions are measured as shown in Figure 3.1.

Framing and Clearances

Figure 3.1 Dimensions

14 in.

[356mm]

15-1/2 in.

[394mm]

[292mm]

11-1/2 in.

8 in.

[203mm]

[112mm]

4-3/8 in.

5-1/4 in.

4-3/4 in.

2-1/4in.

10 in.

[254mm]

[135mm]

[57mm]

2-1/4in.

[57mm]

[121mm]

[241mm]

9-1/2 in.

12-1/2 in.

[318mm]

[159mm]

6-1/4 in.

1-1/2 in.

[38mm]

Front View Without Cover

Front View With Cover

Side View

Back View

Top view

10 IN.

13 IN.

Framing Dimensions

. Construct a framework as shown in Figure 3.2.

Framework material should be the same dimensions as

the material used for the wall framing. The dimensions

of the box must be 10 inches high by 13 inches wide.

. Cut a 10 inch high by 13 inch wide opening into the

exterior of the structure. Stay inside of the newly

installed framing as shown in Figure 3.2.

Figure 3.2

Содержание PVLP-SLP


































Результаты поиска

Содержание PVLP-SLP

Отзывы:

Бренды по названию

Популярные бренды

Hearth and Home Technologies PVLP-SLP, Руководство по установке

Результаты поиска

Содержание PVLP-SLP

Отзывы:

Бренды по названию

Популярные бренды