4
21. Do not change the incline of the treadmill by
placing objects under the treadmill.
22. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
23. When using iFIT.com CDs and videos, an
electronic “chirping” sound will alert you
when the speed and/or incline of the treadmill
is about to change. Always listen for the
“chirp” and be prepared for speed and/or in-
cline changes. In some instances, the speed
and/or incline may change before the per-
sonal trainer describes the change.
24. When using iFIT.com CDs and videos, you
can manually override the speed and incline
settings at any time by pressing the speed
and incline buttons. However, when the next
“chirp” is heard, the speed and/or incline will
change to the next settings of the CD or video
program.
25. Always remove iFIT.com CDs and videos from
your CD player or VCR when you are not
using them.
26. Inspect and properly tighten all parts of the
treadmill regularly.
27. Never insert or drop any object into any
opening.
28.
DANGER:
Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the main-
tenance and adjustment procedures de-
scribed in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
29. This treadmill is intended for in-home use
only. Do not use this treadmill in any commer-
cial, rental, or institutional setting.
30. If an outside antenna or cable system is con-
nected, be sure that the antenna or cable sys-
tem is grounded to provide some protection
against voltage surges and built-up static
charges. Section 810 of the National
Electrical Code, ANSI/NFPA No. 70-1984, pro-
vides information with respect to proper
grounding of the mast and supporting struc-
ture, grounding of the lead-in wire to an an-
tenna discharge unit, size of grounding con-
ductors, location of antenna discharge unit,
connection to grounding electrodes, and re-
quirements for the grounding electrode.
31. An outside antenna system should not be lo-
cated in the vicinity of overhead power lines
or other electric light or power circuits, or
where it can fall into such power lines or cir-
cuits. When installing an outside antenna
system, extreme care should be taken to keep
from touching such power lines or circuits,
as contact with them might be fatal.
32. To reduce the risk of electric shock, do not re-
move the cover or back of the TV. There are
no user serviceable parts inside. Refer servic-
ing to qualified service personnel.
33. Upon completion of any service or repairs to
the treadmill or TV, ask the service technician
to perform safety checks to determine that
the unit is in proper operating condition (refer
to the drawing on page 6).
• Use No. 10 AWG (5.3mm
2
) copper, No. 8
AWG (8.4mm
2
) aluminum, No. 17 AWG
(1.0mm
2
) copper-clad steel or bronze wire,
or larger as a ground wire.
• Secure antenna lead-in and ground wires to
house with stand-off insulators spaced from
4 to 6 feet (1.22 to 1.83m) apart.
• Mount antenna discharge unit as close as
possible to where the lead-in enters the
house.
• Use a jumper wire not smaller than No. 6
AWG (13.3mm
2
) copper, or the equivalent
when a separate antenna-grounding elec-
trode is used. See NEC Section 810-21 (j).
Note to CATV system installer: This reminder is
provided to call the CATV system installer’s at-
tention to Article 820-40 of the NEC that provides
guidelines for proper grounding and, in particu-
lar, specifies that the cable ground shall be con-
nected to the grounding system of the building,
as close to the point of cable entry as practical.
