HEADQUARTERS OH-58A Скачать руководство пользователя страница 265

Страница: 265 / 292

(1)

Varying degrees of right yaw depending on

power applied and airspeed at time of failure.

(2)

Forward CG shift.

b. Procedure:

(1)

Enter autorotative descent (power off).

(2)

Maintain airspeed above minimum rate of

descent airspeed.

(3)

If run-on landing is possible, complete au-

torotation with a touchdown airspeed above effective

translational lift.

(4)

If run-on landing is not possible, start to

decelerate from about 75 feet altitude, so that forward

groundspeed is at a minimum when the helicopter

reaches 10 to 20 feet; execute the touchdown with a

rapid collective pull just prior to touchdown in a level

attitude with minimum ground run.

9-22. LOSS OF TAIL ROTOR EFFECTIVENESS

(LTE).

This is a situation involving a loss of effective

tail rotor thrust without a break in the drive system which

cannot be stopped with full left pedal application. If LTE

is experienced, simultaneously:

1. Pedal - Full Left.

2. Cyclic - Forward.

3. As recovery is effected, adjust controls for

normal

ight.

Collective reduction will aid In arresting the yaw

rate; however, if a rate of descent has been es-

tablished, collective reduction may increase the

rate of descent to an excessive value. The re-

sultant large and rapid Increase in collective to

prevent ground or obstacle contact may further

increase the yaw rate, decrease the rotor RPM

and cause an overtorque and/or over-temper-

ature condition. Therefore, the decision to re-

duce collective must be based on the pilot as-

sessment of the altitude available for recovery.

If spin cannot be stopped and crash is imminent, an au-

torotation may be the best course of action. Maintain

full left pedal until the spin stops, then adjust to maintain

heading.

9-23. MAIN DRIVESHAFT FAILURE.

A failure of the

main driveshaft will be indicated by a sudden increase

in engine RPM, decrease in rotor RPM, left yaw and

activation of the low RPM audio, and illumination of the

ROTOR RPM warning light. A transient overspeed of

N1 and N2 may occur but will stabilize. In the event of

main driveshaft failure:

1. AUTOROTATE - Establish a power-on

autorotational glide. The engine must

continue to operate at normal operating

RPM in order to provide tail rotor control.

2. EMER SHUTDOWN after landing.

9-24. CLUTCH FAILS TO DISENGAGE.

A clutch

failing to disengage in

ight will be indicated by the

rotor RPM decaying with engine RPM as the throttle

is reduced to the engine idle position when entering

autorotational descent. This condition results in total

loss of autorotational capability. If a failure occurs:

1. Throttle - Open.
2. LAND AS SOON AS POSSIBLE.

9-25. MAST BUMPING.

LAND AS SOON AS POSSIBLE.

9-26. FIRE.

The safety of helicopter occupants is the

primary consideration when a

re occurs; therefore, it is

imperative that every effort be made by the

ight crew

to put the

re out. On the ground, it is essential that the

engine be shut down, crew and passengers evacuated

and

ghting begun immediately. If time permits, a

"MAYDAY" radio call should be made before the electri-

cal power is off to expedite assistance from

ghting

equipment and personnel. If the helicopter is airborne

when a

re occurs, the most important single action that

can be taken by the pilot is to land the helicopter.

Toxic fumes of the extinguishing agent may

cause injury, and liquid agent may cause frost-

bite or low temperature burns.

Change 14 9-9

TM 55-1520-228-10

Содержание OH-58A





































































































































































































































































































Результаты поиска

Содержание OH-58A

Отзывы:

Похожие инструкции для OH-58A

Бренды по названию

Популярные бренды

HEADQUARTERS OH-58A, Техническое руководство

Результаты поиска

Содержание OH-58A

Отзывы:

Похожие инструкции для OH-58A

Бренды по названию

Популярные бренды