HddSurgery Seagate 7200.10 Скачать руководство пользователя | Manualshive

Страница: 19 / 27

background image

Page

19

of

27

HDDSURGERY

Lomina 33, 11 000 Belgrade, Serbia

phone +381 11 361 43 43

www.hddsurgery.com

[email protected]

Tools for data recovery experts

33.

Unscrew the upper cylinder and then unscrew the butterfly-screws holding the hard
drive in place.

Unscrewing the upper cylinder

34.

Pull out the hard drive from the tool, unscrew the 4 screws holding the

platter holder

and remove the platter holder. Screw those 4 screws back in place. Place the lid back on
the hard drive and start cloning the drive.

For a more detailed instruction on how to use this tool, check the video guide and

animation which can be found on our website:

You can find more information about this tool and many other tools used for data
recovery on our website.

http://www.hddsurgery.com/

Video guide

«
...
17
18
19
20
21
...
»

Содержание Seagate 7200.10




























Отзывы:

Нет отзывов

Похожие инструкции для Seagate 7200.10

LITTLE BIG DISK THUNDERBOLT 2

Бренд: LaCie Страницы: 6

Бренд: DANE-ELEC Страницы: 2

Бренд: SanDisk Страницы: 2

Бренд: morse Страницы: 6

HIMALAYA 100.S/2/CC

Бренд: garofalo Страницы: 12

Бренд: U-Line Страницы: 5

Бренд: Patiowell Страницы: 27

MY PASSPORT EDGE

Бренд: Western Digital Страницы: 77

G-DRIVE mobile USB

Бренд: G-Technology Страницы: 32

H-Post Shelving

Бренд: Hallowell Страницы: 7

REPLACE TAPE DRIVE IN STORAGELOADER VXA...

Бренд: Tandberg Data Страницы: 10

SiliconEdge Blue Series

Бренд: Western Digital Страницы: 2

Бренд: Yardmaster Страницы: 28

Бренд: NCR Страницы: 12

Бренд: Accu Страницы: 44

Flexline CompactContainer

Бренд: Oka Страницы: 12

Бренд: XtendLan Страницы: 14

Бренд: QNAP Страницы: 49

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды