HDBaseT HDBTM44 Скачать руководство пользователя страница 66

Страница: 66 / 67

4x4 HDMI 2.0 HDBaseT Matrix Switcher

11. Troubleshooting & Maintenance

Problems

Potential Causes

Solutions

Output image with snowflake.

Bad quality of the connecting

cable.

Try another high-quality cable.

Fail or loose connection.

Make sure the connection is good.

No output image when

switching.

No signal at the input / output

end.

Check with oscilloscope or

multimeter if there is any signal at the

input/ output end.

Fail or loose connection.

Make sure the connection is good.

The product is broken.

Send it to authorized dealer for

repairing.

POWER

indicator doesn’t

work or no respond to any

operation.

Fail connection of power cord.

Make sure the power cord

connection is good.

EDID management does not

work normally.

The HDMI cable is broken at

the output end.

Change for another HDMI cable

which is in good working condition.

Static becomes stronger when

connecting the video

connectors.

Bad grounding.

Check the grounding and make sure

it is connected well.

Cannot control the device by

control device (e.g. a PC)

through RS232 port.

Wrong RS232 communication

parameters.

Type in correct RS232

communication parameters.

Broken RS232 port.

Send it to authorized dealer for

checking.

Cannot control the device by

front panel buttons while can

control it through RS232 port

The front panel buttons are

locked.

Send command

/%Unlock;

to unlock

the front panel buttons.

Note: If your problem still remaining after following the above troubleshooting steps,
please contact your local dealer or distributor for further assistance.

Содержание HDBTM44




































































Результаты поиска

Содержание HDBTM44

Отзывы:

Похожие инструкции для HDBTM44

Бренды по названию

Популярные бренды

HDBaseT HDBTM44, Руководство пользователя

Результаты поиска

Содержание HDBTM44

Отзывы:

Похожие инструкции для HDBTM44

Бренды по названию

Популярные бренды