HBM GEN3i Скачать руководство пользователя страница 864

Страница: 864 / 1160

Figure E.49:

Installing display languages

Log off for the changes to take effect (this will affect only the user profile
under which you are currently logged on).

Note

If the required language is not listed, install the required language as described
in "Installing a Language Pack in Windows 7 Ultimate" on page 868.

E.7.2

How to change the Windows 10 display language

Note

Windows

10 removed all language packs at the end of a Customer Image

Restore. Therefore the user must always install the language pack in
Windows

10 to make the change of the Windows

10 display language

obsolete.

GEN3i

864

I3763-3.1 en HBM: public

Содержание GEN3i









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание GEN3i

Отзывы:

HBM GEN3i, Руководство пользователя, Страница: 864 / 1160

Результаты поиска

Содержание GEN3i

Отзывы: