HBM GEN3i Скачать руководство пользователя страница 868

Страница: 868 / 1160

E.7.3

Installing a Language Pack in Windows 7 Ultimate

Note

Make sure that GEN3i has access to an internet connection. The Windows

update needs access to Microsoft

servers to download the selected language

pack.

Go to

Start

►

All Programs

►

Windows Update

►

Optional Updates.

Open optional updates and go to the section

Windows 7 Language

Packs

Figure E.53:

Optional updates

GEN3i

868

I3763-3.1 en HBM: public

Содержание GEN3i









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание GEN3i

Отзывы:

HBM GEN3i, Руководство пользователя, Страница: 868 / 1160

Результаты поиска

Содержание GEN3i

Отзывы: