background image

 

IS23510VSP  Rev-C 

Hayward Pool Products 

620 Division St, Elizabeth, NJ 07207 

Phone: (908) 355-7995 

www.hayward.com 

 

MaxFlo VS

 500

                                                                   

Owner’s Manual

 

 

 

 

                                                                                    Model  SP23510VSP 

  MaxFlo VS 500 Variable Speed Pump 

 

Hayward’s MaxFlo VS 500 variable speed pump delivers incredible energy savings via its advanced 

hydraulic design combined with a totally enclosed, permanent magnet motor.  The MaxFlo VS 500 pump 

is easily installed either as a programmable stand-alone pump or with a Hayward or third party 

controller and features an easy-to-use digital control interface that can be mounted in four different 

positions on the pump or removed and mounted on the wall for total user convenience. 

 

Note:

 To prevent potential injury and to avoid unnecessary service calls, read this manual carefully and 

completely. Unless otherwise stated, instructions in this manual apply to both pump models.

 

SAVE THIS INSTRUCTION MANUAL 

Содержание MaxFlo VS 500

































Отзывы: