USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
Set Countdown Timer
The Light Controller offers a countdown timer function for
your pool and spa light(s). When activated, the lights will
stay on for a predetermined amount of time set by the
user, then turn off automatically. To set the countdown
timer follow the procedure below. When selecting the
duration, note that each lit LED represents 1 hour. The
total number of LEDs that are lit = the total duration in
hours. The lights will automatically turn off at the end of
the countdown duration.
The example below shows that the lights will stay on for
2 hours and then automatically shut off.
The Light Controller will indicate that a new countdown
timer has been set by blinking LED 5 (see LED Indicator
Codes) and then revert to Show/Color mode.
Set Recurring Schedule
The procedure to set a schedule is identical to setting a
countdown timer, except that the ENTER button is held for
3 seconds at the end of the procedure. Once set, the lights
will turn on daily at the same time each day and stay on for
the duration that was selected. If the lights are already on,
they will change to the scheduled color or show.
The example below shows that the lights will turn on
automatically every day (beginning immediately after the
schedule is saved) and shut off after 2 hours.
The Light Controller will indicate that a new schedule has
been set by blinking LED 4 (see LED Indicator Codes) and
then revert to Show/Color mode.
Cancelling a Countdown Timer or Schedule
The procedure for cancelling a countdown timer or a
schedule is identical. Push and hold both the SCHEDULE
button and the ENTER button for 3 seconds. The Light
Controller will cancel the existing settings and will revert
to Show/Color mode.
The Light Controller will indicate that a countdown timer
or schedule has been cancelled by blinking LED 6 (see
LED Indicator Codes).
Resync
Occasionally the Light Controller may have to be re-
synchronized with the lights due to a power interruption
or other type of communication error. In that case, press
and hold the Resync button for 3 seconds. The Light
Controller will initiate a re-synchronization process that
will re-establish communication with the pool/spa lights.
This may take up to 1 minute.
Factory Reset
To clear all previous settings, press the SHOW/COLOR and
RESYNC buttons and hold for 3 seconds.
The Light Controller will indicate a factory reset by blinking
LED 7 (see LED Indicator Codes).
Warranty and Other Languages
Refer to hayward.com for other languages and warranty
information.
ColorLogic Light Controller
Owner’s Manual
LKCUS1100
LKCUB1100
092582 RevA
Push the
SCHEDULE
button
Select the number
of hours (each lit
LED = 1 hour)
Push and hold the
ENTER button for 3
seconds to save
Push and hold the
SCHEDULE and
ENTER buttons for
3 seconds
Push and hold the
RESYNC button for
3 seconds
®
Briefly push
the ENTER
button to
save
Rotate CENTER
KNOB to select
desired color or
show
Briefly push the
CENTER KNOB to
save
1
2
LED Indicator Codes
The Light Controller can indicate certain conditions by
blinking the front LEDs. Refer to the following conditions
and their corresponding indicator codes (LED 1 is at the
12 o’clock position, LED 2 is the 1st LED after the 12
o’clock position, etc.).
Condition
Indicator Code
Same Selection
LED 1 blinking
Overload
LED 2 blinking
Busy
LED 3 blinking
Recurring Schedule
LED 4 blinking
One Time Countdown
LED 5 blinking
Timer Reset
LED 6 blinking
Factory Reset
LED 7 blinking
Processing Request All LEDs in a circular pattern
3
4
5
6
Wait until all
LEDs stop
blinking
Push the
SCHEDULE
button
Rotate CENTER
KNOB to select
desired color or
show
Briefly push the
CENTER KNOB to
save
1
2
3
4
Wait until all
LEDs stop
blinking
Select the number
of hours (each lit
LED = 1 hour)
5
6
Hayward Pool Products
620 Division Street, Elizabeth NJ 07207
Phone (908)-355-7995
www.hayward.com
