Hayman Reese 03257RW Скачать руководство пользователя страница 13

 

49-75 Pacific Drive Keysborough, VIC 3173 
Phone: 1800 812 017 
Email: [email protected]

 

 

 

 

CUSTOMER INFORMATION 

PLACE THESE INSTRUCTIONS IN THE 

VEHICLE’S GLOVEBOX AFTER INSTALLATION 

Rev: 

A

 

 

 

 

 

 

 

Page 

13

 

 

 

 

 

            Issue Date: 

03-05-19

 

 

THANK YOU FOR PURCHASING HAYMAN REESE.  
WITH CORRECT MAINTENANCE AND CARE THIS PRODUCT WILL PROVIDE A 
LIFETIME OF TROUBLE-FREE OPERATION.  

 

TOWBAR MAINTENANCE AND CARE: 

 

 

1.  Hayman Reese recommend that the towbar LUG or TBM (tow ball Mount) Pull Pin and R-clip are removed 

and stored when not in use. Removal of LUG or TBM (tow ball mount) is advisable when not in use to 
assist with any of the following.  

 

 

 

Ensure rear number plate is not obscured.  

 

 

 

Allow maximum available departure angle and prevent any potential interference.  

 

 

 

Prevent possible interference with vehicles reverse sensors or camera detecting a tow ball mount 
as an obstruction during reversing.  

 

Removes towball mount as an obstruction for when moving around the rear of the vehicle.  

 

2.  Hayman Reese recommends routine inspection of your towbar to ensure trouble free towing.  

 

 

 

Bolt security and tension should be regularly inspected and checked for correct tension. Replace 
any worn or defective parts with suitable grade & class fasteners. Inspection should be requested 
to coincide with vehicle major services.  

 

3.  It is the owner’s responsibility to ensure towing and down ball weight capacities of the towing vehicle are 

not exceeded.  

 

 

 

Towing and down ball weights allowable may differ according to model variations. Please refer to 
owner’s manual or vehicle dealer to confirm exact rating for your vehicle model variant.  

 

 

 

It is not uncommon for the vehicle tow rating to differ from the towbar rating. When this occurs, 
the lesser rating must be adhered to.  

 

For vehicles fitted with enhanced vehicle functions that may be altered/changed when towing i.e 
Trailer sway mitigation, blind spot detection, adaptive cruise control etc. Please consult owner’s 
manual to understand changes enabled when towing and after towing. 

 

 

 

 

WARRANTY INFORMATION: 

 

 

Hayman Reese Towbars are covered by a Lifetime Warranty.  
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are 
entitled to a replacement or refund for a major failure and for compensation for any other reasonably 
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to 
be of acceptable quality and the failure does not amount to a major failure.  
For further details please visit www.haymanreese.com.au/warranty or contact customer service on  
1800 812 017 or [email protected]

 

Содержание 03257RW















Отзывы: