Haws 1011HO Скачать руководство пользователя страница 3

 

 

09/20 

MODEL 1011HO/1011HO2/1011HPSHO/1011HPSHO2 

PAGE 3 OF 7 

 

 

 

INSTALLATION PROCEDURE…

 

 
STEP 1

:  Thoroughly flush supply line to remove all foreign matter. Connect 

1/2” IPS supply 

screwdriver-stop (not supplied) to stub-out in wall. Install sup

ply 3/8” O.D. tubing 

(supplied), between screwdriver-stop and solenoid valve (Cut tubing to proper length 
and follow general notes for proper connection procedures for push-in type fittings). 
Connect 3/8

” O.D. tube between fountains and solenoid valve outlet(s) (if not already 

connected).  

 

STEP 2

:    Open screwdriver-stop 

wide open

 while checking for leaks at all connections. Also, 

check waste for leaks. 

 

STEP 3

Model 1011HO/1011HPSHO (only): 5874 Series Valve 

– 

Adjust bubbler stream 

height using a small flat-head screwdriver inserted through a hole in the center of the 
push button for increased flow turn clockwise and for decreased flow turn 
counterclockwise. If flow problems arise, see troubleshooting guide for additional 
instructions to correct problem. Bubbler stream may lower during short break-in 
period. Set initial stream height a little high to minimize or eliminate the need for 
break-in period readjustment. 

 

 
                  

Model 1011HO/1011HPSHO/1011HO2/1011HPSHO2: 5867 Valve Pressure 

Regulator 

 Adjust bubbler stream height using the black pressure regulator 

mounted inside bracket that has HO sensor unit, by loosening the locknut and 
rotating the knob clockwise to increase flow or counterclockwise to reduce flow. 
Tighten the locknut and check flow height. Repeat these steps until the bubbler flow 
height is correct. 

 

STEP 4:  RKHO Series Transformer and Sensor Setup: Refer to the RKHO Series manual 

for instructions (supplied). 

 

MAINTENANCE 

 

 

STEP 1: 

Periodically clean the strainer located in the push button valve body on Models 
1011HO/1011HPSHO (Refer to 5874 Series Valve Manual for more information). 

 

      

 

5874 Series VALVE TROUBLESHOOTING (Models 1011HO/1011HPSHO Only) 

 

PROBLEM 

 

REPAIR CHECKLIST 

1.  Insufficient bubbler flow. 

1a.  Check that inlet screwdriver stop valve (not 

supplied) is in wide-open position.  

 

 

  b.  Verify minimum 30 psi flowing supply pressure. 

 

 

  c.  Clean strainer. See 5874 Series Valve Manual. 

 

 

  d.  Adjust valve to increase flow. Use front adjust 

screw or see 5874 Series Valve Manual. 

 

 

e. 

Clean screens (inside nozzle body). Unscrew 
nozzle insert and very gently activate water 
supply to pop out qty. 3 screens (be careful not 
to lose screens). Remove any debris clogging 
the screen openings and place back into nozzle 
body. Reassemble nozzle insert. 

 

For more information about Haws products, see our website

www.hawsco.com

 

 

© 2020 Haws

®

 Corporation 

– All Rights Reserved 

HAWS

® 

and other trademarks used

 

in these materials are the exclusive property of Haws Corporation. 

Содержание 1011HO








Отзывы: