Hawkeye Mfg AGCO RoGator A Series Скачать руководство пользователя | Manualshive

Страница: 23 / 54

background image

4

Nozzle Body and Nozzle Control Valve Installation: Hawkeye® 2 Nozzle Body Installation

19

NOZZLE BODY AND NOZZLE CONTROL VALVE INSTALLATION

AGCO SPRAY BOOMS WILGER NOZZLE BODY ASSEMBLY

1. Locate the components provided to assemble the two configurations of the nozzle bodies.

FIGURE 3. Wilger Nozzle Body Configurations

2. Remove the stainless steel U-clip provided with the nozzle bodies.
3. Align the nozzle body or plug as necessary and reinstall the U-clip to secure.
4. If the Wilger-to-Square lug tip adapters are needed to accommodate the tips to be used, install them on the

outlets of the nozzle bodies by rotating them a quarter turn.

FIGURE 4. Outlets of the Nozzle Body

Center Section

of Machine

Boom Wings

A

B

Square Lug Tip

Adapters Installed

«
...
21
22
23
24
25
...
»

Содержание AGCO RoGator A Series























































Отзывы:

Нет отзывов

Похожие инструкции для AGCO RoGator A Series

Бренд: Makita Страницы: 20

Бренд: UnderCover Страницы: 16

Бренд: Safco Страницы: 6

Бренд: FeiYu Tech Страницы: 5

Бренд: FEIYUTECH Страницы: 19

Бренд: FeiYu Tech Страницы: 25

Бренд: FEIYUTECH Страницы: 16

Бренд: Hagan Страницы: 32

Бренд: Padwico Страницы: 28

Бренд: Olympus Страницы: 2

XMODS Custom RC

Бренд: Radio Shack Страницы: 4

Бренд: Wallbox Страницы: 7

Бренд: Paradyne Страницы: 4

Бренд: Rice Lake Страницы: 2

Бренд: Wagan Страницы: 8

Бренд: ADIC Страницы: 6

Бренд: Thermo King Страницы: 2

Бренд: Camcar Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды