Haussmann Xpert PNT116 Скачать руководство пользователя страница 19

TROUBLESHOOTING

WARRANTY

ENGLISH

SYMPTOM

PROBABLE CAUSE

CORRECTIVE ACTION

Tool runs slowly. Air 

flows slightly from 

exhaust

 Dirt particles jammed in 

motor.

 Power regulator in closed 

position

 Air flow blocked by dirt. 

Compressor not sufficient 

to operate tool.

 Check air inlet filter for blockage.

 Pour air tool lubricating oil into air inlet as per 

instructions.

 Operate tool in short bursts quickly reversing rotation 

back and forth where applicable.

 Repeat above as needed.

Tools will not run. Air 

flows freely from exhaust

 One or more motor vanes 

stuck due to material build 

up.

 Pour air tool lubricating tool into air inlet.

 Operate tool in short bursts of forward and/or reverse 

rotation where applicable.

 Tap motor housing gently with plastic mallet.

 Disconnect supply. Free motor by rotating drive shank 

manually where applicable. If problem persists, contact 

customer service for repair.

Tool will not shut off

 Throttle valve “O-rings” 

dislodged from seat inlet 

valve.

 Replace ‘O’ rings.

19

Thank you for investing in a HAUSSMANN XPERT power tool. These products have 

been made to demanding, high-quality standards and are guaranteed for domestic use 

against manufacturing faults for a period of 36 months from the date of purchase.

This guarantee does not affect your statutory rights. In case of any malfunction of your 

tool (failure, missing part, etc.), please contact one of our service technicians at our toll 

free service line at 1-866-206-0888 from 8 AM to 6 PM, Monday to Friday, Eastern 

time. RONA reserves the right to repair or replace the defective tool, at its discretion.

The product is guaranteed for 36 months if used for normal trade purposes. Any 

guarantee is invalid if the product has been overloaded or subject to neglect, improper 

use or an attempted repair other than by an authorized agent. Heavy-duty, daily 

professional or hire usage are not guaranteed. Due to continuous product 

improvement, we reserve the right to change the product specification without prior 

notice.

REGISTER YOUR PRODUCT

We invite you to register your product online to make future communications easier. 

To do so, simply visit our website www.haussmanntools.com.

Содержание PNT116




















Отзывы: