Haulotte Group HA12CJ, Книга по эксплуатации

Страница: 24 / 146

24 4000360350 E12.14 USA/GB
HA12CJ - HA32CJ - -
B
- Recommendations
Specific labels ANSI
Specific labels, optional
3.1.5 - Green labels
3.1.6 - Blue labels
N.B.-:-The blue labels indicate information or a precaution to be taken in case of danger.
Green labels indicate maintenance, operations or information (CSA standard).
A29 A22
O3
WARNING
DANGER
. This machine is not insulated.
. Maintain a clearance of at least 10 ft. between any part of machine or load and any electrical line or apparatus charged up to 50,000 volts.
. One foot additional clearance is required for each additional 30,000 volts or less.
. Allowances must be made for operator error, machine deflection and electrical line swaying.
Machine must be on a smooth, firm and level surface before swinging, elevating and/or
extending boom.
DO NOT exceed platform rated capacity.
Make sure the operating surface will support the machine.
DO NOT drive with platform raised, or raise platform, when on uneven, sloping or soft
surfaces including trucks, trailers, railway cars, floating vessels, scaffolds or similar areas.
DO NOT raise platform during high winds.
DO NOT drive near drop offs, holes or other hazards.
Make sure all tires are in good condition and air filled tires are properly inflated.
To drive on a slope, boom must be retracted, lowered below horizontal and centered
between the rear wheels.
Driving with boom above horizontal or extended is restricted to smooth, firm and
level surfaces free of obstructions.
FALLING HAZARD
TIP OVER HAZARD
Check the condition of the approved fall protection device, lanyard and the designated
attachment point to the platform.
Wear approved fall protection items and attach to marked locations.
Keep both feet on platform floor.
Ensure entrance area is properly closed.
DO NOT use planks, ladders or similar items in platform to get added reach.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
CRUSHING HAZARD
Always look in the direction of movement
.
Keep clear of obstructions.
.
Direction of drive and steer functions are opposite to the motion of the controls when the
platform is positionned over the front axle end.
Always look at the decals on the chassis and drive / steer control for proper direction.
.
Keep all body parts inside of platform during operation.
.
Death or serious injury could result from a tip-over
Falling from platform could cause death or serious injury
Failure to follow instructions could result in death or serious injury
THIS MACHINE MUST NOT BE USED UNTIL IT IS INSPECTED AND OPERATING PROPERLY.
DO NOT operate this machine unless you have been properly trained as described in the HAULOTTE Operation and Safety Manual by a
qualified person and authorized to operate this machine. Your training includes reading and understanding the safety, operating and
maintenance instructions in manufacturer's manuals, knowing your employers work rules and applicable governmental regulations.
Follow the instructions in the Operating Manual and sections 6, 7 and 8 of ANSI A92.5-2006 for daily, frequent and annual inspections.
These may be obtained from your authorized HAULOTTE, Inc. equipment dealer or HAULOTTE, Inc.
DO NOT replace items (i.e., batteries, tires, counterweight, etc.) with items of different weight or specification because this will affect
the stability of the machine.
DO NOT modify or change this machine without written approval from the manufacturer.
Operate this machine with extreme caution. STOP all operation if a malfunction occurs.
Test foot switch for proper operation.
RECOMMENDATIONS FOR USE
DAILY INSPECTION
Test high engine and high drive cut out switches for proper operation.
DO NOT wash the electrical components with a washer pressure.
DO NOT use the machine as a welding earth.
DO NOT weld on the machine without first disconnecting the battery terminals.
Check the level of diesel fuel (for diesel engine platform).
Check that there are no apparent defects (hydraulic leaks, loose bolts, loose
electric connections).
Check that the tilt indicator operates correctly by sounding the buzzer (when
machine is raised).
.
.
.
.
.
.
.
.
.
.
.
.
.
INSTRUCTION BEFORE USE
Remove the rotation locking pin (if there is a turntable).
IMPORTANT when using the AC power line to the work platform, the power plug
must be connected to an electrical installation protected by a circuit breaker.
START-UP
Turn the battery isolater switch to the "ON" position.
Unlock the emergency stop button then press the
starter button (for diesel engine platform).
If the machine does not start, wait 10 seconds
then repeat the operation.
The machine must not be used while charging
the batteries (on electrical machine)
Improper use of this machine could
cause death or serious injury.
.
.
.
.
.
ELECTROCUTION
HAZARD
Death or serious injury will occur
from contact or being too
close to electrical lines.
7815 017 c
Minimum safe approach distance
(M.S.A.D) to energized (exposed or
insulated) power lines
Voltage Range
(Phase to phase)
Minimum safe approach distance
0 to 300 V
Over 300 V to 50 kV
Over 50 kV to 200 kV
Over 200 kV to 350 kV
Over 350 kV to 500 kV
Over 500 kV to 750 kV
Over 750 kV to 1000 kV
AVOID CONTACT
10
15
20
25
35
45
3.05
4.60
6.10
7.62
10.67
13.72
3078147890 c
(Feet) (Meters)
A8