background image

SKU 95419   

For technical questions, please call 1-800-444-3353. 

PAGE 2

SAVE THIS MANUAL

You  will  need  this  manual  for  the  safety  warnings  and  precautions,  assembly, 
operating, inspection, maintenance and cleaning procedures, parts list and assembly 
diagram.  Keep your invoice with this manual.  Write the invoice number on the inside 
of the front cover.  Keep this manual and invoice in a safe and dry place for future 
reference.

GENERAL SAFETY WARNINGS AND PRECAUTIONS

1. 

KEEP WORK AREA CLEAN AND DRY.  Cluttered, damp, or wet work areas 
invite injuries.

2. 

KEEP CHILDREN AWAY FROM WORK AREA.  Do not allow children to handle 
this product.

3. 

STORE IDLE EQUIPMENT.  When not in use, tools and equipment should be 
stored in a dry location to inhibit rust.  Always lock up tools and equipment, and 
keep out of reach of children.

4. 

DO NOT USE THIS PRODUCT IF UNDER THE INFLUENCE OF ALCOHOL OR 
DRUGS.  
Read warning labels on prescriptions to determine if your judgement or  

PRODUCT SPECIFICATIONS

Maximum Weight Capacity

1,450 lb.

Bed Dimensions

4 Ft. x 8 Ft.

Hitch Ball Size

1-7/8”

Wheel Rim Diameter/Width

12” x 4”

Quantity Wheel Lug Nuts

4 Per Wheel

Tire Size

4.80 - 12

Required Tire Air Pressure

60 PSI

Overall Dimensions

110” L x 61-1/2” W x 19-1/4” H

Trailer Weight

266 lb.

Содержание 95419























Отзывы: