Harris NEXIO AMP Generation 6 Скачать руководство пользователя страница 34

Страница: 34 / 76

Chapter 3

System Installation

175-100423-00

To Rack Mount NXAMP3801HDX/HDI

Ensure that the rack is anchored to the floor so that it cannot tip over when
NXAMP3801HDX/HDI is extended out of the rack.

Figure 3-1

Rack Mounting

Remove the slides from the rails.

Attach a slide to each side of the NXAMP3801HDX/HDI chassis using seven screws per side.

Make sure the release latch is located at the back of the chassis.

Attach an extension to the back of each rail to match the depth of your rack.

Attach the rails to the rack posts.

Pull the inner rail out until it locks.

Slide the NXAMP3801HDX/HDI into the rail until it stops; press the release latch on each slide and

continue to slide the NXAMP3801HDX/HDI into the inner rail all the way into the rack.

To Remove NXAMP3801HDX/HDI from a rack

Stand in front of the NXAMP3801HDX/HDI and pull the NXAMP3801HDX/HDI out until it locks in place.

Press the release button on the outside of each inner rail, and pull the NXAMP3801HDX/HDI out of the

rack.

Содержание NEXIO AMP Generation 6













































































Результаты поиска

Содержание NEXIO AMP Generation 6

Отзывы:

Похожие инструкции для NEXIO AMP Generation 6

Бренды по названию

Популярные бренды

Harris NEXIO AMP Generation 6, Руководство по установке оборудования и инструкция пользователя

Результаты поиска

Содержание NEXIO AMP Generation 6

Отзывы:

Похожие инструкции для NEXIO AMP Generation 6

Бренды по названию

Популярные бренды