Harmonic Ellipse 3000 Скачать руководство пользователя страница 274

Страница: 274 / 403

Chapter 10 Unit Configuration

274

Ellipse 3000 Release 3.0, Rev. B

Ellipse System Sub-Menu/Tab

10.3.4

Ethernet Port (Management) Menu

Use the Ethernet Port (Management) menu to set or view the following management port
parameters:

■

■

■

■

NOTE:

The default, factory set values of these parameters may not be compatible with the user’s network and

must be configured to the environment where the encoder is installed.

The following sections detail the Ethernet Port (Management) menu options and parameters.

Front Panel

To access the

Ethernet Port (Management)

menu on the front panel:

❖

Navigate

Root > Configuration > Unit > System > Ethernet Port (Management)

Web Manager

To access the

Ethernet Port (Management)

parameters in the Web Manager:

❖

Select

Unit > System

Ethernet Port (Management)

IP Address

010.041.012.101

Subnet Mask

255.255.000.000

Default Gateway

010.041.012.001

MAC address

00:0C:A2:06:F4:30

Содержание Ellipse 3000















































































































































































































































































































































































































Результаты поиска

Содержание Ellipse 3000

Отзывы:

Похожие инструкции для Ellipse 3000

Бренды по названию

Популярные бренды

Harmonic Ellipse 3000, Руководство пользователя

Результаты поиска

Содержание Ellipse 3000

Отзывы:

Похожие инструкции для Ellipse 3000

Бренды по названию

Популярные бренды