Harmonic Ellipse 3000 Скачать руководство пользователя страница 276

Страница: 276 / 403

Chapter 10 Unit Configuration

276

Ellipse 3000 Release 3.0, Rev. B

Ellipse System Sub-Menu/Tab

10.3.4.3

Default Gateway

The

Default Gateway

parameter sets the Default Gateway address used by the device. The

Gateway address must be from the same subnet as the Ethernet Management port IP address.

The available value is of IP address type: xxx.xxx.xxx.xxx.

Front Panel

To set the

Default Gateway

parameter on the front panel:

❖

Navigate

Root > Configuration > Unit > System > Ethernet Port (Management) > Default

Gateway

Web Manager

To set the

Default Gateway

parameter in the Web Manager:

❖

Select

Unit > System

10.3.4.4

MAC Address

The MAC address displays in the Ethernet Port box in the web manager and under the Ethernet
Port menu on the front panel.

Default Gateway

010.041.012.001

Содержание Ellipse 3000















































































































































































































































































































































































































Результаты поиска

Содержание Ellipse 3000

Отзывы:

Похожие инструкции для Ellipse 3000

Бренды по названию

Популярные бренды

Harmonic Ellipse 3000, Руководство пользователя

Результаты поиска

Содержание Ellipse 3000

Отзывы:

Похожие инструкции для Ellipse 3000

Бренды по названию

Популярные бренды