background image

© 2018Harmar Mobility, LLC • All Rights Reserved

|  www.harmar.com

14

Pinnacle Stair Lift

COMPLETION PROCEDURES

Completion Procedures

A. TEST ARMREST CONTROL SWITCH

1. Ensure that the unit travels correctly by 
operating the armrest control switch while 
standing in front of the unit.

2. Depress the switch in the upstairs direction to 
move up. The lift will begin to smoothly accelerate 
upwards. The lift will continue to move upwards 
as long as the switch is depressed.

3. Release the switch and the lift will come to an 
immediate stop.

4. Depress the switch in the downstairs direction 
to move down. The lift will begin to smoothly 
accelerate downwards.

5. Release the switch and the lift will come to an 
immediate stop.

6. Run the chair all the way up and down the 
rail to ensure that the top of the seat back has 
at least a 1/2

"

 clearance from the wall and any 

obstructions. 

B. TIGHTEN BRACKETS

1. Install and fully tighten the rail bracket 
mounting screws (three (3) screws per bracket). For 
hardwood stairs, a pilot hole should be drilled first. 
For plywood or particle board stairs care must be 
taken to prevent stripping.

C. SET UPPER AND LOWER TRAVEL LIMITS

1. Test the lower travel limit by operating the lift 
downward, keeping the switch depressed. The unit 
should begin to decelerate about 3

"

 from its final 

resting position and stop clear of the floor.

2. The final stopped position can be adjusted 
to accommodate the height of the user by 
repositioning the limit cam located in a slot in the rail.

3. Use a 5/64

"

 Allen wrench to loosen the set screw 

in the limit cam. Adjust the limit cam up or down and 
retighten the set screws. Repeat the above steps until 
the lift stops in the desired position.

4. Repeat the above steps to set the upper limits. 
For safety, the footrest should be set at least level 
with the upper landing.

5. The optimum position is met when the seat 
height above the floor is the same at the top and 
bottom of the stairs.

D. TEST SAFETY STOP SWITCHES

1. Safety stop switches are located in both the 

upward and downward ends of the chassis 

providing protection from obstructions on the rail.

2. Safety stop switches are located in the 

footrest bottom pan providing protection from 

obstructions and trapping hazards on the stairs.

3. A safety stop switch is part of the swivel seat 

mechanism and prevents the lift from operating 

when the swivel is in use.

4. Test all the safety stop switches by driving the 

lift down and touching the downward end of the 

chassis, the lower edge of the footrest, and the 

underside of the footrest in both its folded and 

unfolded positions.

5. In each of the above cases the unit should come 

to an immediate halt. The LED indicator light on 

the armrest control should turn to orange and the 

unit should beep intermittently.

6. When the control switch is released, the unit 

should NOT be able to be driven in the direction 
that the lift initially engaged the obstacle. Test this 
condition.

WARNING

Do not ride on the chassis or lift 

until the install is complete.

Содержание SL600FR-LH





















Отзывы:

Похожие инструкции для SL600FR-LH