Harmar Mobility Pinnacle Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 16

Harmar Mobility Pinnacle Скачать руководство пользователя страница 2

Pinnacle HD Stair Lift Manual |

| www.Harmar.com | 866-351-2776

2

P/N: 75403 RevB 72618

Table of Contents

Table of Contents

Read and understand this manual prior to attempting stair lift installations. Please refer to the Owner’s Manual for
Limited Warranty information and operating instructions. The Owner’s Manual must be given to the owner of the
lift before it is put into service.

Any alterations to the equipment without written authorization by the manufacturer may void the warranty.
Harmar lifts are designed to require as little assembly by the installer as possible. If you have questions, concerns
or comments, please contact Harmar’s Technical Service Department at 1-866-378-6848 or
[email protected].

CONTENTS:

Important! It is imperative that this manual be read and understood prior to attempting installation of the stair lift.

Please observe all cautions and warnings in this manual, and on equipment labels.

I. PRELIMINARY CHECKS ................................................................3

A. Tools required ..............................................................3

B.

Included

parts...............................................................3

II. INSTALLATION PROCEDURES ....................................................4

A. Determine rail length...................................................4

B.

Rail

installation..........................................................5-6

C.

Chassis

installation.......................................................7

D. Final rail installation.....................................................8

E. Footrest and seat installation................................9-12

III. REMOTE CALL/SEND CONTROL OPERATION.......................13

A. Remote control operation.........................................13

B. Remote control reprogramming..............................13

IV. COMPLETION PROCEDURES ...................................................14

A. Test armrest control switch.......................................14

B.

Tighten

brackets.........................................................14

C. Set upper and lower travel limits............................14

D. Test safety stop switches..........................................15

E. Additional System Checks.........................................16

«
1
2
3
4
...
»

Содержание Pinnacle

















Отзывы:

Нет отзывов