SAFETY:
Caution:
Do not operate this lift until your dealer has satisfactorily instructed you in the proper operation of the lift.
Your Harmar lift has been engineered and designed for years of trouble free use. Although, with everyday use,
some parts may become loose or worn.
IMPORTANT!
Check regularly for any worn, loose or damaged parts of
your lift.
If anything is observed, DO NOT USE THE LIFT!
Contact your dealer or installer of the lift for repairs to
be
made. Failure to act may cause severe injury!
Your Harmar lift should only be used for the loading and unloading of scooters and power wheelchairs for which it is
designed. DO NOT add to or modify any part of the lift system without first contacting the manufacturer of the lift.
Any modifications may void any warranties as well as effect the structural integrity of the lift.
Always make sure the vehicle’s parking brake is firmly set before operating the lift.
Caution:
When using the lift, keep your hands and feet from under the scooter or power chair as it is being loaded
or unloaded.
Warning:
This lift is not meant for human transport. The mobility device and platform must be unoccupied before
operating the lift.
MAINTENANCE:
The Harmar lift has been designed to be as trouble free as possible for the owner. But, as with any mechanical device,
regular care should be given while owning and using this device. Maintenance should be performed regularly.
We recommend that dealers schedule a preventative maintenance inspection at least once a year on motors, lift
frame, wiring harness and all moving parts of the lift.
Check for paint chips and touch up any bare metal with a good gloss black enamel or lacquer to inhibit rust. This
may be necessary more frequently when subjected to salt air or road salt.
TROUBLESHOOTING:
PROBLEM
: The lift will
not operate or operates slowly.
Possible Cause -
Verify the vehicle harness is tightly attached to the
battery and there is no build-up of corrosion.
12 volts should be present at the end connector,
but does not indicate full function.
Bad Connection
- THE #1 CAUSE OF PROBLEM LIFTS
SAFETY & MAINTENACE
P R O B I N G F O R 1 2 V O L T S M A Y I N D I C A T E
A C O N N E C T I O N , B U T N O T N E C E S S A R I L Y
A S U F F I C I E N T C O N N E C T I O N .
T H E L I F T ’ S M O T O R C A N D R A W U P T O
3 0 A M P S A T S O M E P O I N T S , R E Q U I R I N G
A L L O F T H E W I R E A VA I L A B L E T O F L O W
P R O P E R C U R R E N T . P O O R C O N N E C T I O N S
ARE THE #1 PROBLEM ASSOCIATED WITH
A SLOW, WARM, POORLY PERFORMING MOTOR.
NOT ONLY WILL THE MOTOR PERFORM POORLY,
B U T W I L L P R E M A T U R E LY D E T E R I O R A T E .
I F A S I N G L E S T R A N D O F A M U LT I -
S T R A N D W I R E I S M A K I N G C O N T A C T.
12V WILL APPEAR ON THE METER, OR TEST LIGHT,
BUT WILL NOT ALLOW THE MOTOR TO OPERATE
T O I T S F U L L P O T E N T I A L .
I T I S A L W AY S B E S T T O T E S T B O T H
CURRENT AND VOLTAGE, OR RUN THE MOTOR
WITH KNOWN GOOD SHOP BATTERY OR POWER
S O U R C E W H E N T R O U B L E S H O O T I N G .
PROBLEM
: Intermittent power to the lift. The lift will operate for
a short period of time and quit. At a later time it will
start working again.
Possible Causes:
Circuit Breaker
- Although the breaker resets itself automatically, it
may be malfunctioning and need to be replaced.
Bad Connection
- Verify the vehicle’s wiring harness is tightly attached
to the battery and there is no build up on the terminals
Hand Control
- Test by bypassing the hand control. Do this for only
a second or two. The lift, vehicle, scooter or chair may
be damaged if continuos power is supplied to the unit
Verify all connectors terminals are well seated, and not
retracted back into the body of the connector.
PROBLEM
: Platform will not sit level on the ground.
Possible Causes:
Terriain
- Verify the vehicle is parked on flat level ground
Orientation of the lift’s base
- Adjust the four leveling feet until
the platform sits on level ground
IMPORTANT NOTE FOR ANY ACCESSORY VEHICLE LIFT
14