background image

4

IMPORTANT SAFETY INSTRUCTIONS

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with a dry cloth.

Do not block any ventilation openings. Install in accordance with the manufacturer’s 
instructions.

Do not install near any heat sources such as radiators, heat registers, stoves, or other 
apparatus (including amplifiers) that produce heat.

Do not defeat the safety purpose of a polarised or grounding type plug.  A polarised 
plug has two blades with one wider than the other.  A grounding type plug has two 
blades and a third grounding prong.  The wide blade or the third prong are provided 
for your safety.  If the provided plug does not fit into your outlet, consult an electrician 
for replacement of the obsolete outlet

Protect the power cord from being walked on or pinched particularly at plugs, conven-
ience receptacles and the point where they exit from the apparatus.

Only use attachments/accessories specified by the manufacturer.

Use only with the cart, stand, tripod, bracket or table specified by the manufacturer, 
or sold with the apparatus.  When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.

Unplug this apparatus during lightning storms or when unused for long periods of 
time.

Refer all servicing to qualified service personnel.  Servicing is required when the ap-
paratus has been damaged in any way, such as power-supply cord or plug is damaged, 
liquid has been spilled or objects fallen into the apparatus, the apparatus has been 
exposed to rain or moisture, does not operate normally, or has been dropped.

Note: It is recommended that all maintenance and service on the product should be 
carried out by Soundcraft or its authorised agents.  Soundcraft cannot accept any li-
ability whatsoever for any loss or damage caused by service, maintenance or repair 
by unauthorised personnel.  
WARNING:  To reduce the risk of fire or electric shock, do not expose this apparatus 
to rain or moisture. 
Do not expose the apparatus to dripping or splashing and do not place objects filled 

Содержание MFXi























































Отзывы: