manualshive.com logo in svg

Harman Martin Exterior 400 Series, Руководство пользователя

Поделиться
Скачать
Harman Martin Exterior 400 Series Скачать руководство пользователя страница 11

Physical installation

 11

Power and DMX data cable layout

Figure 7 gives an overview of a suitable cable layout. The dotted lines represent AC power 
circuits. The solid lines represent the data link.

Cables and cable glands

The power cable supplied with the product is 9.5 mm (0.37 in.) external diameter. The data cable is 6.5 mm 
(0.25 in.) external diameter. If you install these cables in cable glands in the installation (when connecting 
cables in external junction boxes, for example), make sure that the cable glands are designed to accept 
these cable diameters.

The IPON

®

 IP68-rated cable glands used for power and data cable entry into the fixture accept cable with 5 

- 10 mm (0.2 - 0.4 inch) external diameter. If you replace a cable, install a new rubber seal or a complete 
cable gland if the seal is not in perfect condition. If you use a cable with an external diameter that is not 
within the range accepted, replace the cable gland with a suitably dimensioned item. Cable glands must be 
rated IP68 and suitable for the cable diameter and application. New cable glands can be obtained from 
Martin™ (P/N 13102000) or from electrical suppliers. 

To replace an IPON cable gland:

1. Lock out power to the installation and allow it to cool for 20 minutes.

2. Loosen the dome nut in the existing gland to release the cable, then unscrew the gland from the rear 

cover.

3. Remove the rear cover from the fixture, note connections and disconnect the cable from its terminals.

4. Slide the old gland off the cable.

5. Screw the new gland into the rear cover until it is tight enough to make a seal. Do not overtighten.

6. Pass the cable through the new gland and rear cover, then connect it to its terminals (with reference to 

“Replacing the power cable” on page 13 or “Connection pinouts” on page 15 if necessary).

7. Reinstall the rear cover as follows:

a. Read“Managing humidity” on page 7.

b. Check that the seal is in perfect condition.

c. Place the seal and cover in position and drive the cover screws until they are finger-tight only.

d. Cross-tighten the screws evenly in a diagonal pattern, increasing torque gradually in stages to a 

maximum torque of 8 Nm (5.9 ft.-lbs.).

8. Tighten the dome nut on the cable gland to seal the cable before applying power.

OPTO-

SPLITTER

Power

230V AC

50 Hz

50 Hz

Power

230V AC

50 Hz

Max. 32 luminaires

or 500m. before

opto-splitter

is required.

Max. 32 luminaires

or 500m. before

opto-splitter

is required.

OPTO-

SPLITTER

DMX

Universe #1

Universe #1

DMX

Universe #2

AC power

Fixture

Fixture

Fixture

OPTO-

SPLITTER

Power

230V AC

50 Hz

Power

230V AC

50 Hz

Max. 32 luminaires

or 500m. before

opto-splitter

is required.

OPTO-

SPLITTER

DMX

Universe #1

DMX

Universe #2

Universe #2

AC power

Fixture

Fixture

Fixture

OPTO-

SPLITTER

Power

230V AC

50 Hz

50 Hz

Power

230V AC

50 Hz

Max. 32 luminaires

or 500m. before

opto-splitter

is required.

Max. 32 luminaires

or 500m. before

opto-splitter

is required.

OPTO-

SPLITTER

DMX

Universe #1

Universe #1

DMX

Universe #2

AC power

Fixture

Fixture

Fixture

Figure 7: Schematic cable layout diagram

Содержание Martin Exterior 400 Series









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды