background image

18

18

7.4 Play from the Bluetooth source

Through Bluetooth, stream audio play on your Bluetooth device 
to the soundbar.
1.  Check that the soundbar has been properly connected to 

your Bluetooth device (See “Bluetooth connection” in the 
“CONNECT” chapter).

2.  To select the Bluetooth source, press 

 

on the soundbar or 

  

on the remote control.

3.  Start audio play on your Bluetooth device. 

4.  Adjust the volume on the soundbar or your Bluetooth device.

7.5 Play through Chromecast

Through Chromecast, stream audio on your Android or iOS 
device to the soundbar. 
1.  On the soundbar, 

a)  Check that the soundbar has been properly connected 

to your home network (See “Connection with your home 
network” in the “CONNECT” chapter).

b)  Check that the soundbar has been switched on or to 

standby mode. 

2.  On your Android or iOS device, 

a) Check that your Android or iOS device has been 

connected to the same network as the soundbar.

b)  On a Chromecast-enabled app, play music, tap the cast 

icon 

 and select the connected soundbar.

CHROMECAST 

3.  To exit from the music playback, switch to other sources. 

7.6 Play through AirPlay

Through AirPlay, stream audio on your iOS device to the soundbar. 
1.  On the soundbar, 

• 

Check that the soundbar has been properly connected 
to your home network (See “Connection with your home 
network” in the “CONNECT” chapter).

2.  On your iOS device, 

a)  Check that your iOS device has been connected to the 

same network as the soundbar.

b)  To enter the Control Center on an iOS device, swipe down 

from the upper right corner (iOS 12 or later) or swipe up 
from the bottom edge (iOS 11 or earlier). Tap   to select 
the connected soundbar and then, start audio streaming 
from an app.

usic 

ining Room speaker 

Phone 

AIRPLAY

3.  To exit from the music playback, switch to other sources. 

NOTES:

 

The soundbar can support audio streaming and cannot support video 
streaming.

 

During Chromecast or AirPlay, music playback pauses on the current 
connected device when you start music playback on a second 
connected device.

 

When the soundbar switches between your home Wi-Fi and wired 
network during AirPlay 2, music playback pauses and will resume in 
a few minutes, depending on  the bandwidth condition of broadband.   
For the connection to your home wired network, see Step 3 under 
“Connection with your home network” in the Chapter “CONNECT”.

Содержание JBL BAR 9.1


























Отзывы: