Harman Crown T Series Скачать руководство пользователя страница 11

page 7

T-Series Operation Manual

Specifications

Guaranteed Minimum Power

T3

T5

T7

T10

4 ohms stereo (per channel)

8 ohms stereo (per channel)

8 ohms bridge mono

(1 kHz (EIA) with 0.5% THD)

450W

330W

900W

750W

500W

1500W

950W

675W

2000W

1350W

1000W

2700W

Performance

Frequency Response (at 1 watt)

20 Hz – 20 kHz, +0/-1 dB

Total Harmonic Distortion (THD)

<0.5%, 20 Hz – 20 kHz

Intermodulation Distortion (IMD) 

(60 Hz and 7 kHz at 4:1, from full rated output to -30 dB)

= / <0.35%

Slew Rate

>10V/us

Voltage Gain

31 dB

33 dB

34.4 dB

36 dB

Damping Factor (8 ohms, 10 Hz – 400 Hz)

>200

Signal-to-Noise Ratio 

(below rated power, 20 Hz to 20 kHz, A-weighted)

>100 dB

Crosstalk (below rated power)

At 1 kHz: -75 dB

At 20 kHz: -59 dB

Input Sensitivity (for full rated power at 8 ohms)

0.775V or 1.4V

Nominal Input Impedance

Balanced: 20k ohms

Unbalanced: 10k ohms

Connectors, Controls and Indicators

Input Connectors

One balanced XLR and one unbalanced RCA per channel

Output (speaker) Connectors

4-pole Speakon® and one pair binding post per channel

Front Panel Controls

Power on/off switch, one gain control per channel

Rear Panel Controls

Output mode switch: stereo (dual), parallel or bridge

Input sensitivity switch: 0.775V or 1.4V

Power Indicator

One blue LED

Signal Indicator

One green LED per channel

Clip (peak) Indicator

One yellow LED per channel

Fault Indicator

One red LED per channel

Power Cord Specifications

Plug: 10A, 250V

Cord: CCC 3 x 1.5 mm

2

Construction

Protection

Protection against short circuits, no-load, on/off muting, and RF interference;

stable into reactive or mismatched loads

Ventilation

Flow-through ventilation from front to back

Cooling

Internal heat sinks with forced air. Fan cooled, speed regulated, thermal protection

Dimensions (W x H x D)

19 x 3.46 x 12.45 in

(482 x 88 x 316.4 mm)

19 x 3.46 x 14.5 in

(482 x 88 x 369 mm)

Net Weight

28.0 lb

(12.7 kg)

29.7 lb

(13.5 kg)

39.9 lb

(18.1 kg)

43.0 lb 

19.5 kg)

Shipping Weight

32.4 lb

(14.7 kg)

34.2 lb

(15.5 kg)

44.4 lb

(20.1 kg)

47.4 lb

(21.5 kg)

Содержание Crown T Series














Отзывы: