manualshive.com logo in svg

Harman crown PIP Series, Справочное руководство, Страница: 8 / 16

Поделиться
Скачать
Harman crown PIP Series Скачать руководство пользователя страница 8

Networked PIP Series

Reference Manual

page 8

Installation

Before beginning, please carefully note:

CAUTION: STATIC ELECTRICITY MAY DAMAGE THE UNIT.

 Use caution 

when handling the unit. Carefully ground yourself BEFORE touching the unit. Avoided 

unnecessary touching the components or solder pads on the circuit board. It is best to 

handle the unit by its front panel only. 

Prepare the PIP

 

The PIP comes ready to install in the amplifier. This unit does not require setting the “IQ 

address” as the older current loop, Crown bus, units did. Each PIP (as well as all network 

components) comes preprogrammed with a unique network (MAC) address. The HiQnet 

address is then set (automatically or manually) via SystemArchitect control software (TCP/

IP network address).

Prepare the Amplifier

 

Turn down the amplifier level controls (full counterclockwise) and turn off 

the amplifier.

Disconnect the amplifier’s power cord.

Remove the existing PIP module from the amplifier back panel (two screws).

Install the PIP into the Amplifier.

 

Carefully ground yourself to the chassis of the amplifier

 before installing the 

PIP, it is a good idea to maintain ground contact between yourself and the amplifier while 

inserting the module into the amplifier.

Prepare the Cables

Before using the AUX port, and after the 

PIP-Lite

 module  

has been installed into the amp, make sure to pass the 

CAT5 cable twice through the supplied ferrite core.

Important:

 On CTs3000 and CTs2000 models, make sure to add the supplied ribbon 

cable ferrite core to the end of the B cable before connecting to the PIP module. Its location 

will be similar to the ferrite on the A cable, with ½ to 1 inch of cable between the connector 

and ferrite core. The core is not required on CTs600 and CTs1200 amplifiers.

Before using the PIP-USP4-CN, after it is installed into the amp, make sure to use ferrite 

cores for cables connecting to the Analog, AES, AUX and Network ports as follow:

1.  Pass all the Analog Input and Output cables 

through a ferrite core (one time).

2.  Pass the AES, AUX and Network cables 

three (3) times through a ferrite core. 

Use a separate core of each the cables.

www.audiovias.com

Содержание crown PIP Series

















Отзывы:

Нет отзывов