Harman AMX DXLINK DX-RX-4K Скачать руководство пользователя

Страница: 17 / 91

Product Overview and Specifications

Hardware Reference Manual – DXLink™ Twisted Pair 4K Transmitters/Receivers

COMPATIBILITY NOTE:

DXLink Twisted Pair 4K Transmitters and Receivers are compatible with other DXLink Twisted Pair 4K

products (see the Compatible AMX Products listed in the table above). Wallplate Transmitters require an approved DXLink power

injector (see table above) when connecting directly to a Receiver. AMX does not support the use of power supplies other than the one

provided or power injectors other than those listed as they may potentially damage DXLink equipment. For compatibility between

DXLink Twisted Pair 4K and DXLink Twisted Pair equipment, see the “DXLink Compatibility Appendix” on page 89.

Twisted Pair Cable Type

• Shielded Cat6A or Cat7

NOTE:

or more details and helpful cabling information, reference the white paper titled

“Cabling for Success with DXLink” available at www.amx.com or contact your AMX

representative.

Twisted Pair Cable Length

Up to 262 ft. (80 m) for full 4K signal support.

Up to 328 ft. (100 m) for 1080p and below.

IMPORTANT:

DXLink twisted pair cable runs for DXLink equipment shall only be run within a

common building. “Common building” is defined as: Where the walls of the structure(s) are

physically connected and the structure(s) share a single ground reference.

Modules - Airflow

Convection (openings on top of case)

Transmitters and Receiver

Inter-compatibility

All DXLink Transmitters can connect directly to DXLink Receivers. All Wallplate Transmitters require

either PDXL-2 (FG1090-170) or PS-POE-AT-TC (FG423-84) to do so.

Other AMX Equipment

AMX Products Compatible with

DXLink Transmitters

• DX-RX-4K
• DGX-I-DXL-4K

NOTE:

DXLink Twisted Pair 4K Transmitters are also compatible with DXLink Twisted Pair

equipment (see the “DXLink Compatibility Appendix” on page 89).

AMX Products Compatible with

DXLink Receivers

• 4K HDMI Wallplate TX
• DGX-O-DXL-4K
• SDX-414-DX
• SDX-514M-DX
• SDX-814-DX

NOTE:

DXLink Twisted Pair 4K Transmitters are also compatible with DXLink Twisted Pair

equipment (see the “DXLink Compatibility Appendix” on page 89).

Included Accessories

Desktop power supply (ENERGY STAR

qualified): 1 per module

IMPORTANT:

Only the provided desktop power supply should be used, and it must not be

altered in any way.

Compatible / Optional Equipment

• CC-NIRC NetLinx Emitter Cable (FG10-000-11)
• IR03 External IR Receiver Module (FG-IR03)
• PDXL-2 (FG1090-170)
• PS-POE-AT-TC (FG423-84)

NetLinx and Control Specifications

Parameter

Value

ICS LAN / Ethernet Port

(Module Only)

• TCP/IP port (ICS LAN 10/100)
• RJ-45

Serial (Module Only)

• Bidirectional RS-232
• Standard NetLinx baud rate 1200 to 115K
• Parity support: Odd/Even/None
• 3.5 mm pluggable Phoenix terminal block

IR Control (Module Only)

• Port for use with IR03 Receiver (optional accessory FG-IR03)
• Port for use with CC-NIRC Emitter (optional accessory FG10-000-11)

Advanced Configuration Interface

USB mini-B connector (Program port)

ID Pushbutton

• Toggle between DHCP and static IP addressing
• Places system in NetLinx Device ID assignment mode
• Reset the factory default settings
• Restore the factory firmware image

General Specifications

Twisted pair Cable

Specs

Содержание AMX DXLINK DX-RX-4K




























































































Результаты поиска

Содержание AMX DXLINK DX-RX-4K

Отзывы:

Похожие инструкции для AMX DXLINK DX-RX-4K

Бренды по названию

Популярные бренды

Harman AMX DXLINK DX-RX-4K, Справочник по аппаратуре

Результаты поиска

Содержание AMX DXLINK DX-RX-4K

Отзывы:

Похожие инструкции для AMX DXLINK DX-RX-4K

Бренды по названию

Популярные бренды