manualshive.com logo in svg

Harman AMX DXLINK DX-RX-4K, Справочник по аппаратуре

Поделиться
Скачать
Harman AMX DXLINK DX-RX-4K Скачать руководство пользователя страница 89

Appendix G - DXLink Compatibility

89

Hardware Reference Manual – DXLink™ Twisted Pair 4K Transmitters/Receivers

Appendix G - DXLink Compatibility

Overview

While DXLink Twisted Pair 4K hardware is intended for primary use with other DXLink Twisted Pair 4K hardware (full capability 

compatibility), it is also compatible with DXLink Twisted Pair hardware. When DXLink Twisted Pair 4K is used in conjunction with 

DXLink Twisted Pair hardware, Input and Output signal support matches the lowest common denominator (e.g., if you want to use 

the DX-TX with the DX-RX-4K, the DX-RX-4K will behave exactly like a DX-RX). See the tables below for compatibility between 

hardware types. 

Compatibility with DXLink Twisted Pair Endpoints

By default, DXLink 4K Input Boards provide a 4K EDID to all connected DXLink Transmitter devices. While DXLink Transmitters are 

supported by the DXLink 4K Input Board, the default EDID provided to the Transmitter may result in a source device (computer, 

media player, etc) presenting a video resolution out of the Transmitter's range. To ensure the source device presents a resolution 

the DXLink Transmitter can support, simply use the Enova DGX 100 Series System Configuration interface to select a non-4K EDID 

(All, Wide, Full in non-4K range) to ensure a supported format is requested by the DXLink Transmitter.

NOTE: 

All of the DXLink Twisted Pair Transmitters (i.e., DX-TX, DX-TX-WP, and DX-TX-DWP) must be running firmware version 1.8.23 or 

later for compatibility with the DX-RX-4K. Likewise, the 4K HDMI Wallplate TX is only compatible with the DX-RX if the Receiver is 

running firmware version 1.13.24 or later. 

* This configuration of equipment supports USB HID between endpoints. Serial and IR Control is only supported between modules, 

not wallplate and module pairs (see the 

DXLink Twisted Pair Transmitters/Receiver Hardware Reference Manual

).

Compatibility with Enova DGX DXLink Twisted Pair Input and Output Boards

NOTE: 

4K HDMI Wallplate TX and 4K RX are compatible with Enova DGX DXLink Twisted Pair Input and Output Boards in an Enova DGX 

100 Series enclosure, but DXLink Twisted Pair 4K Transmitters and Receivers attached to DXLink Twisted Pair equipment truncate 

signal support to match the capabilities of the DXLink Twisted Pair equipment.

Compatibility with Solecis Digital Switchers

Compatibility with Enova DVX Presentation Switchers

DXLink Twisted Pair Endpoints

DXLink Twisted Pair 4K Endpoints

Compatibility

DX-TX module*

DX-RX-4K module

Yes, endpoint or extender mode

AVB-TX-HDMI-DXLINK module 

(discontinued)* 

DX-RX-4K module

Yes, endpoint or extender mode

DX-TX-WP*

DX-RX-4K module

Yes, endpoint or extender mode

DX-TX-DWP*

DX-RX-4K module

Yes, endpoint or extender mode

DX-RX module

DX-TX-DWP-4K

Yes, endpoint or extender mode

Enova DGX DXLink Twisted Pair 

Input and Output Boards

DXLink Twisted Pair 4K Endpoints

Compatibility

DGX-I-DXL

DX-TX-DWP-4K

Yes, 4 inputs per board

DGX-O-DXL

DX-RX-4K

Yes, 4 outputs per board

Solecis Digital Switchers

DXLink Twisted Pair 4K Endpoints

Compatibility

SDX-410-DX 4x1

DX-RX-4K

1 output

SDX-510M-DX 5x1

DX-RX-4K

1 output (powered)

SDX-810-DX 8x1

DX-RX-4K

1 output

Enova DVX Presentation Switchers DXLink Twisted pair 4K Endpoints

Compatibility

DVX-3x56HD

DX-TX-DWP-4K
DX-RX-4K

4 inputs (powered)
2 outputs

DVX-3x55HD

DX-TX-DWP-4K
DX-RX-4K

2 inputs (powered)
2 outputs

DVX-3x50HD

DX-RX-4K

2 outputs

DVX-2x55HD

DX-TX-DWP-4K
DX-RX-4K

2 inputs (powered)
1 output (powered)

DVX-2x50HD

DX-TX-DWP-4K

1 output (powered)

Содержание AMX DXLINK DX-RX-4K




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды