Harman Accentra Скачать руководство пользователя страница 20

20

3-90-00674R20_08/12

mobile home Installation

CAuTION

ThE STOvE IS hOT whIlE IN OPErATION.

kEEP ChIldrEN, ClOThINg ANd FurNITurE 

AwAY.  CONTACT mAY CAuSE SkIN burNS.

kEEP COmbuSTIblE mATErIAlS SuCh AS 

grASS, lEAvES, ETC. AT lEAST 3 FEET 

AwAY FrOm ThE POINT dIrECTlY uNdEr 

ThE vENT TErmINATION.

wArNINg

When installing and operating your Harman Accentra 

Insert,  respect  basic  safety  standards.  Read  these 

instructions carefully before you attempt to install or 

operate the Accentra Insert. Failure to do so may result 

in damage to property or personal injury and  may void 

the product warranty.

Consult  with  your  local  building  code  agency  and 

insurance  representative  before  you  begin  your 

installation  to  ensure  compliance  with  local  codes, 

including the need for permits and follow-up inspections.

CAuTION: This appliance must be vented to the 

outside.

Due to high temperatures, this stove should be placed 

out of traffic and away from furniture and draperies.

Children and adults should be alerted to the hazards 

of high surface temperatures and should stay away  to 

avoid burn to skin and/or clothing.

Young children should be carefully supervised when 

they are in  the same room as the stove.

Clothing and other flammable materials should not be 

placed on or near this stove.

Installation and repair of this stove should be done by 

a qualified service person. The appliance should be 

inspected before use and at least annually by a qualified 

service person. More frequent cleaning will be required. 

It is imperative that control compartments, burners, and 

circulating air passageways of this stove be kept clean.

Safety reminders

mobile home Installation

mobile  home  installation  should  be  done  in 

accordance with the manufactured home and Safety 

Standard (hud), CFr 3280, Part 24. 

When installing the Accentra in a mobile home several 

requirements must be followed: 

1. The unit must be bolted to the floor. This can be done 

with 1/4" lag screws through the 5 holes in    the base 

plate shown in Fig. 26.

2. The unit must also be connected to outside air. See 

page 22. All mobile home installations require the use 

of outside air, this will increase the heating efficiency of 

the unit and keep it from suffering any effects associated 

with room air starvation such as poor combustion and 

or erratic operation. Periodically check the air inlet for 

any obstructions such as snow or ice build up.

Kitchen exhaust fans, clothes dryers and other similar 

devices  may  cause  improper  operation  of  the  pellet 

stove, if, while in use, it keeps the room in a negative 

pressure,  thus  allowing  pipe  joints,  not  completely 

sealed, to leak exhaust into the room. Be sure to allow 

adequate ventilation while using such appliances 

3. Floor protection and clearances must be followed. 

Floor protection and clearances to combustibles must 

be followed as per installation instructions for the stove. 

Clearances may only be reduced by means approved 

by the regulatory authority.

4.  Unit  must  be  grounded  to  the  metal  frame  of  the 

mobile home.

5. Smoke alarms and smoke detectors are recommended 

to be used with wood and biomass fueled stoves. When 

opening the firebox door some exhaust may escape into 

the room and set off the alarm. If this should happen 

ventilate  the  room  to  remove  the  smoke  and  reset 

the alarm, if the alarm would go off when no one was 

working with the stove ventilate the room and have your 

home checked to find the source of the leak.

CAuTION 

ThE STruCTurAl INTEgrITY OF ThE mObIlE 

hOmE FlOOr, wAll, ANd CEIlINg/rOOF 

muST bE mAINTAINEd.

wArNINg

mObIlE/mANuFACTurEd hOmE guIdElINES 

dO NOT AllOw INSTAllATION IN A SlEEPINg 

rOOm.

wArNINg 

uSE OF ImPrOPEr FuElS, FIrE STArTErS 

Or AlTErINg ThE STOvE FOr hIghEr hEAT 

OuTPuT mAY CAuSE dAmAgE TO ThE STOvE 

ANd COuld rESulT IN A hOuSE FIrE. uSE 

ONlY APPrOvEd FuElS ANd OPErATION 

guIdElINES

Содержание Accentra

















































Отзывы: