manualshive.com logo in svg

Harman Stove Company PP38+, Инструкция по установке и эксплуатации

Поделиться
Скачать
Harman Stove Company PP38+ Скачать руководство пользователя страница 12

P38+ Pellet Stove

13

Fig. 14

Turbo Control

When the Feed Rate is set to "1" and the
Blower is set to the lowest setting, only 75
watts of electricity are used.

Start
Position

Feed  Rate

Turning the  knob passed  the "OFF"  position starts  the

combustion blower and makes the stove ready to light as shown
in  fig 14.  The distribution  blower and  feed motor  will also  run
for one minute or less just to let you know they are operational.

After lighting the fire, the ESP probe in the exhaust senses

when  the  temperature is  high enough  to start  the feed  motor
and distribution  blower.

The  feed  motor will  start and  stop as  needed to  main-

tain a fire relative to the dial setting of the feed rate.

Turbo  Range

Turning the feed rate knob into the Turbo Range causes

the feed  rate to  increase, providing  extra heat  not available  in
the normal  range. It  also causes  the distribution  blower to  go
to  full speed.  This is  because you  are asking  for extra  heat
output, therefore,  full blower  speed is  required.

Blower  Speed Adjustment

This knob adjusts the blower speed  from "Low" to  "Hi"

as desired. When the feed rate is turned into the Turbo Range,
the  blower automatically  goes to  high to  force maximum  heat
into  the  room. The  blower speed  cannot be  varied  when  in
Turbo  Range.

When  a  thermostat  is  connected,  the  blower is  con-

trolled  by  heating  demands.

Thermostat  ( optional  )

When a  thermostat is  connected to  the stove  it controls

the heat  output. When  the  thermostat  calls for  heat, the  feed
rate  and blower  go to  "max"  just  like  in  Turbo Range. When
the  thermostat is  satisfied, the  feed rate  and blower  speed
drop to the level set on the dials.

OFF

When the  Feed Rate  dial is  turned to  the OFF  position

the fire will slowly die and go out. When the stove cools down
enough, all  motors will  stop.

If the stove runs out of pellets and cools down, the

control will  shut down  all but  the combustion  blower.
The control must be turned to OFF to stop the combus-
tion blower.

 Whenever the stove runs out of pellets, the con-

trol must  be turned  to OFF  and then  back to  the desired  set-
ting to  reset the control  for start-up.

Test  Mode

To use test mode, turn the feed rate to OFF and then to

Turbo. This  will cause all  the motors to  run for one  minute or
less  in  order  to  verify operation.  If the  test does  not last  long
enough, simply  recycle test  mode.

Содержание PP38+























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды