Harman Stove Company PF-100 Furnace Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 59

background image

Harman Pellet Service Training

45

Draft Differential Switch

Diaphragm switch which is used to monitor the
negative draft pressure in the firebox. The older blue
switch can be used as a normally open (NO) or
normally closed (NC) switch. In the Harman Pellet
stoves, it is used as normally open. Notice the wire
terminals are labeled NO, and NC The hose ports
correspond to the wiring positions. When built, the
hose port for NC is broken off and the wire terminal
For NC is bent. This is to help prevent improper hook-
up. The feed motor and igniter are wired through this
switch and will not receive power if there is no draft,
or if the draft is too low. The switch actuates at -.17”
W.C. Even though the indicator light may be on
showing power to the feed motor, the switch could still
be intercepting the flow of current. The newer black
switches can only be used as normally open.

«
...
43
44
45
46
47
...
»

Содержание PF-100 Furnace




























































Отзывы:

Нет отзывов

Похожие инструкции для PF-100 Furnace

Бренд: Amana Страницы: 27

Бренд: Carrier Страницы: 58

Бренд: Bryant Страницы: 10

Бренд: Valor Страницы: 12

Бренд: Prestige Страницы: 8

Бренд: USSC Страницы: 28

Бренд: Blue Summit Страницы: 32

Бренд: Carrier Страницы: 60

Бренд: Johnson Страницы: 9

Бренд: Day and Night Страницы: 2

40 THRU 140 MBH

Бренд: York Страницы: 19

Бренд: Solaire Страницы: 26

Бренд: International Comfort Product Страницы: 38

Бренд: Dometic Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды