SUB-TS12 SUBWOOFER AMPLIFIER PANEL CONTROLS AND CONNECTIONS 5
SUB-TS12 SUBWOOFER AMPLIFIER PANEL CONTROLS AND CONNECTIONS
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
harman/kardon
SUB-TS12
For use with
HKTS 12 System
OFF
NORMAL
REVERSE
OOFER LEVEL
ON
AUTO
IMPORTANT: CONNECT STRIPED WIRE TO RED ( ) SPEAKER TERMINAL.
AC 120V~60Hz
POWER
Made in China
⁄
¡
™
¢
∞
¶
‚
§
£
L
R
SUB
PHASE
FILTER
SUBW
GREEN: ON
RED: STAND-BY
LINE
LEVEL
IN
ON
L
R
CONTROL
FILTER
REMOTE
ª
¤
•
¡
Speaker-Level Inputs:
Connect these
binding post terminals to the main left and
right speaker terminals of your receiver or
amplifier, if your receiver or amplifier does
not have a line-level subwoofer output.
Remember to maintain polarity by connecting
the (+) terminal on the receiver/amplifier to the
(+) terminal on the SUB-TS12 subwoofer, and
the (–) terminal on the receiver/amplifier to the
(–) terminal on the SUB-TS12 subwoofer.
™
Speaker-Level Outputs:
If you are
using the
Speaker-Level Inputs
¡
on the
SUB-TS12, you should connect these bind-
ing post terminals to your front left and right
speakers, remembering to maintain polarity
by connecting the (+) terminal on the SUB-
TS12 subwoofer to the (+) terminal on the
speaker, and the (–) terminal on the SUB-
TS12 subwoofer to the (–) terminal on the
speaker. If you are not using the
Speaker-
Level Inputs
¡
, then connect your front
left and right speakers directly to your
receiver or amplifier. See pages 10 through
12 for further information on speaker con-
nections.
£
Line-Level Subwoofer (SUB) Input:
Connect the subwoofer output of a receiver
with digital surround sound decoding, such
as Dolby* Digital or DTS
®
, to this input. This
input bypasses the SUB-TS12’s internal
crossover circuitry, and should only be used
with a filtered signal. If your receiver does not
have digital decoding, you should use the
Line-Level Full-Range Inputs
¢
instead.
¢
Line-Level Full-Range Inputs:
Connect
the line-level subwoofer output or preamp out-
put(s) of your receiver or amplifier to these
inputs. If your receiver does not have a sepa-
rate subwoofer output, use a Y-adaptor (not
supplied) to bridge the receiver’s preamp out-
put to the main amp input for that channel,
and connect the long end of the adaptor
to the corresponding line-level input on the
SUB-TS12. If your receiver has only a single
subwoofer output, you may connect it to
either the left or right line-level input on the
SUB-TS12, and no Y-adaptor is needed.
∞
Phase Switch:
This switch determines
whether the SUB-TS12 subwoofer’s piston-
like action moves in and out in phase with
the main speakers. If the speakers were to
¡
Speaker-Level Inputs
™
Speaker-Level Outputs
£
Line-Level Subwoofer (SUB) Input
¢
Line-Level Full-Range Inputs
∞
Phase Switch
§
High-Cut (Low-Pass) Filter Switch
¶
Music-Sense On/Off Switch
•
Filter Remote Control Input
ª
LED Indicator
‚
Subwoofer-Level Control
⁄
Master Power Switch
¤
AC Power Cord