Harman Kardon HK 3390, Руководство по обслуживанию

Страница: 22 / 74

24
TROUBLESHOOTING GUIDE
SYMPTOM CAUSE SOLUTION
Unit does not function when Main • No AC power • Make certain AC power cord is plugged into
Power Switch is pushed a live outlet
• Check to see whether outlet is switch-controlled
Display lights, but there’s no • Intermittent input connections • Make certain that all input and speaker connections
sound or picture are secure
• Mute is on • Press Mute Button
• Volume Control is down • Turn up Volume Control
• Desired source not selected • Press correct Source Selector
• Speakers deactivated • Press Speaker 1 or Speaker 2 Button
• Headphones are in use • Unplug headphones
• Jumper pins between Preamp Outputs • Replace jumper pins or, if external amplifier
and Main-Amp Inputs were removed is in use, make sure it is turned on
No sound from any speaker; • Amplifier is in Protection mode • Check speaker-wire connections for shorts at receiver and
light around Power Switch is red due to possible short speaker ends
• Amplifier is in Protection mode • Contact your local Harman Kardon service center
due to internal problems
Unit does not respond to • Weak batteries in remote • Change remote batteries
remote commands • Remote sensor is obscured • Make certain front-panel sensor is visible to remote
or connect an optional remote sensor
Intermittent buzzing in tuner • Local interference • Move unit or antenna away from computers, fluorescent
lights, motors or other electrical appliances
Audio sources sound distorted • CD player or other audio device • Only plug a device into the Phono Inputs if it is a
incorrectly plugged into Phono Inputs turntable with a moving-magnet cartridge, or if it is a
turntable with a moving-coil cartridge with a phono preamp
• Turntable not plugged into Phono Inputs • Do not use a turntable with any inputs other than the Phono
Inputs, unless it has a moving-magnet-type cartridge and
includes a phono preamp
No video image • Source device’s video output not • Connect the source’s composite video output to
connected to HK 3390 the correct video input on the HK 3390
• Wrong source selected • Press the correct Source Selector on the HK 3390
• Video Monitor Output not connected • Connect the HK 3390’s Video Monitor Output to a composite
to display video input on your television or video display
• Wrong video input on video • Consult the manual for your television for instructions on
display selected selecting the correct video input
• Audio-only source selected • It is not possible to view video while listening to the
Phono, Tape/CDR or CD sources or to the tuner
In addition to the items shown above, additional information on troubleshooting possible problems with your HK 3390, or on installation-related issues,
may be found in the list of “Frequently Asked Questions,” which is located in the Product Support section of our Web site at www.harmankardon.com.
HK1695 3390OM 4/11/08 3:29 PM Page 24
Processor Reset
If you wish to fully reset the HK 3390 to its factory defaults, or if it behaves erratically after a power surge, first turn the
Master Power Switch off and unplug the AC power cord for at least three minutes. Plug the cord back in and turn the
receiver back on. If this doesn’t help, you may want to try a system reset.
NOTE: A system reset erases all user configurations, including tuner presets. After a reset, you will need to reenter all of
these settings.
Place the receiver in Standby mode by pressing the Power Switch so that the Power Indicator turns amber. Simultaneously
press and hold the front-panel Preset Scan and Mute Buttons for at least five seconds until the software version number,
followed by the RESET message, appear in the display. The unit will return to Standby mode, and you may power it on.
Memory
If the HK 3390 is unplugged or experiences a power outage, it will retain user settings indefinitely.
22
HK3390
harman/kardon