Harken Unit 0 ESP Скачать руководство пользователя страница 6

Страница: 6 / 36

ESP Unit 0, 1

Parts List

Parts Sold Separately/Tools

Furling Line

Unit Part No.

Line Ø

Length (ft)

HFG594

7 mm

HFG233

7 mm

7404 Lead Block Kit

Includes 3 x 7403; 1 x 7401;

1 x 7402; 1 Horn Cleat

Halyard Deflector

Unit

Part No.

7301

7302

Optional Parts

Rod Rigging: Harken Rod Adapter Stud Required

Rod Size

Thread

Size UNF

Part

No.

-4

4.37 mm

7/16"

7420 -4

-6

5.03 mm

7421 -6

-8

5.72 mm

7422 -8

-10

6.35 mm

7423 -10

Short Leg Kit with Toggle

Do not use with turnbuckle

Medium Leg Kit with Toggle

Required for turnbuckle

Long Leg Kit with Toggle

Required for turnbuckle

Unit

Part No.

Clevis

Pin

Part No.

Clevis

Pin

Part No.

Clevis

Pin

7320.20

—

7320.21

7321.20

7321.22

7321.21

Required Parts

Required parts sold separately by Harken:

• Extra foil and connector if required. See pages 7 - 8.

• Harken Short Leg Kit with toggle. Do not use with turnbuckle.

• Harken Medium or Long Leg Kit with toggle. Required for turnbuckle.

• Rod rigging requires Harken rod adapter stud.

• Furling line. To purchase elsewhere, figure length required:

Boat foot length of largest sail + 6' (1.8 m).

Optional parts, sold separately by Harken:

• Halyard Deflector. Use when halyard exits very close to stay attachment point.

• 7404 Lead Block Kit and one additional 7403 if necessary. Fits 1" (25 mm) stanchions.

WARNING! Wire that is old

or damaged may break sud-

denly, causing an accident.

Headstay condition should

be checked by a professional

rigger before reusing.

Preassembly

Tools Required

3. Long tape measure

11. Phillips screwdriver

4. Short tape measure

12. Slotted screwdriver

5. Drill bit – 1/8" (3 mm)

13. Needle-nose pliers

6. Power drill

14. Locking Pliers

7. Hacksaw

15. Center punch

8. Side cutters

16. Hammer

9. Rat-tail file

17. Electric Tape (Use to Mark Foil)

10. Straight edge

18. Vise ( Tape Jaws to Protect Foil)

1. Hex keys

Unit

Size

0, 1

5 mm, 6 mm

2. Socket or open end wrench

Unit

Size

10 mm

16 mm

Содержание Unit 0 ESP





































Результаты поиска

Содержание Unit 0 ESP

Отзывы:

Бренды по названию

Популярные бренды

Harken Unit 0 ESP, Руководство по установке

Результаты поиска

Содержание Unit 0 ESP

Отзывы:

Бренды по названию

Популярные бренды