background image

3

Performa

 Winch 

40.2 PTP

Installation and Maintenance Manual- Mod.C

Introduction - Technical characteristics - Outline

Introduction

This manual gives technical information on winch installation and maintenance, including

disassembling and reassembling.

This information is DESTINED EXCLUSIVELY for specialised personnel or expert users.  

Installation, disassembling and reassembling of the winch by personnel who are not experts may 

cause serious damage to users and those in the vicinity of the winch.

Harken

®

 accepts no responsibility for defective installation or reassembly of its winches.

In case of doubt the Harken

®

 Tech Service is at your disposal at [email protected]

This Manual is available only in English. If you do not fully understand the English language, do 

not carry out the operations described in this Manual.

Technical characteristics

Power ratio 

Gear ratio

1st speed

13,50 : 1

2,13 : 1

2nd speed

39,90 : 1

6,28 : 1

 

The theoretical power ratio does not take friction into account.

Weights

PT version

Weight (Kg)

3,5

 

Maximum working load

WARNING!

The maximum working load (MWL) for the 40.2 PT 

Performa™

 Winch is 850 Kg (1874 lb)

Subjecting the winch to loads above the maximum working load can cause the winch to fail or 
pull off the deck suddenly and unexpectedly during high loads causing severe injury or death.

Outline

Ø80.5

152

82

Ø156

Li

ne

 e

nt

ry

 h

ei

g

ht

Содержание Performa Winch 40.2 PTP

















Отзывы: