manualshive.com logo in svg

Harken 46 Rewind STA EL, Руководство по установке и обслуживанию

Поделиться
Скачать
Harken 46 Rewind STA EL Скачать руководство пользователя страница 4

4

46 Rewind ™ Radial Winch

Installation and Maintenance Manual

Maximum working load

WARNING!

The maximum working load (MWL) for the 46 Rewind™ Winch is 1300 Kg (2866 lb).

Subjecting the winch to loads above the maximum working load can cause the winch to fail or 
pull off the deck suddenly and unexpectedly during high loads causing severe injury or death.

Outline

Installation

The winch must be installed on a flat area of the deck, reinforced if necessary to bear a load equal 
to at least twice the maximum working load of the winch.
It is the installer's responsibility to carry out all structural tests needed to ensure that the deck can 
bear the load.
Harken

®

 does not supply the screws needed to install the winch since these may vary depending 

on the deck on which it is to be installed.
It is the installer's responsibility to choose the correct screws taking account of the loads they will 
have to bear.  
Harken

®

 assumes no responsibility for incorrect installation of its winches or for an incorrect choice 

of mounting screws.

DANGER!

Incorrect  installation  of  the  winch  may  cause  severe  injury  or 

death. Consult the yard that built the boat in the case of doubt 

over the correct positioning of the winch.

Outline - Installation

46 Rewind™ Winch

92 mm

282 mm

192 mm

91 mm

E

203 mm

156 mm

Ø 100 mm

Li

ne entry height

E [mm]

41*
67*

* For different lengths  

refer to pages 26-27

Содержание 46 Rewind STA EL




























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды