30
Chapter
4
•
•
•
•
•
•
Direct Connection:
A direct point-to-point connection between the HI-6500 and your
desktop or laptop computer using any standard Ethernet cable. See
the
Direct Connection
section below.
LAN Connection
To connect the HI 6500 series instrument to a LAN, you simply connect a standard Ethernet
cable between the instrument and the common network hub. You will then need to
determine which scheme is used on the network to assign IP addresses. Every node on the
network must have a unique IP address or conflicts will result.
Contact your Network Administrator for the IP address to use for the instrument.
The IP address can be set manually (Fixed IP), or it can be set automatically by a network
service called DHCP.
NOTE
If the DHCP service fails, the instrument will default to the Fixed IP address after a power
cycle. If the DHCP service is repaired, the instrument will revert back to using the DHCP
IP address.
If you are required to use Fixed IP addresses, refer to the section
Fixed IP Configuration
Using the Front Panel
below. For automatic IP assignment (DHCP), use the following
steps:
DHCP Configuration Using the Front Panel
DHCP works only if a DHCP server is installed on your network.
Step 1. From the Configuration menu, Use the UP or DOWN button to select the
communication menu, then select the Ethernet TCP/IP menu item.
Step 2. Select the DHCP menu item and use the ENTER key to enable/disable this
feature.
Step 3. Select the DHCP IP address menu item and verify that a correct IP address has
been assigned to the instrument by the network server. If an incorrect IP address
has been assigned contact your system administrator; or use a Fixed IP address.
Step 4. This is the IP address to use in your web browser to access the Web Interface.
From here you can jump to the section
NOTE
You cannot change the values of the DHCP IP address. The LEFT button returns the
operator to the Ethernet TCP/IP Menu.
Содержание HI 6500 Series
