Hardi Mercury Covamax series Скачать руководство пользователя

Страница: 84 / 110

6 - Maintenance

1. 14

Drain Valve Seal Replacement

If the main tank drain valve leaks, the seal and seat can be changed
the following way.

•

Remove U-Clip (A) and remove Drain Valve (B)

•

Disassemble drain valve and replace items (C,D,E&F)

•

Reassemble in reverse order

€

DANGER: Make sure tank has been thoroughly emptied and
decontaminated before commencing any work on the fluid
system.

€

DANGER: Do not enter the inside of the tank - the parts can
be changed from the outside of the tank!

WARNING: Use eye / face protection mask when dismantling
the tank drain valve!

Attention: Check function of valve with clean water before filling chemicals into the tank

Drain Valve Cord Replacement

If the main tank drain valve cord is damaged or broken, the cord can be replaced the following way.

•

Remove U-Clip and remove Drain Valve

•

Remove old cord and handle

•

Attach new cord to handle

•

Working from the top of the tank - feed the new cord through the locking guide and down through the drain
valve outlet

•

Reattach cord to drain valve and refit the drain valve into the outlet

•

Gently pull drain valve handle to take up excess cord length

•

Determine correct position for handle and readjust cord fixing at handle to obtain desired cord length.

€

DANGER: Make sure tank has been thoroughly emptied and decontaminated before commencing any work
on the fluid system.

€

DANGER: Do not enter the inside of the tank - the parts can be changed from the outside of the tank!

WARNING: Use eye / face protection mask when removing the tank drain valve!

Attention: Check function of valve with clean water before filling chemicals into the tank

Содержание Mercury Covamax series















































































































Результаты поиска

Содержание Mercury Covamax series

Отзывы:

Похожие инструкции для Mercury Covamax series

Бренды по названию

Популярные бренды

Hardi Mercury Covamax series, Инструкция оператора

Результаты поиска

Содержание Mercury Covamax series

Отзывы:

Похожие инструкции для Mercury Covamax series

Бренды по названию

Популярные бренды