Hardi CT Series Скачать руководство пользователя

Страница: 7 / 52

Function diagram

1. Suction filter
2. Pump
3. Operating unit
4. Pressure gauge
5. Spray lance/boom

Before operation

Electric motor

If the sprayer is equipped with an electric motor it must be connected
by the authorized electrician according to the local law. Adhere to the
law.

Petrol engine

If the sprayer is equipped with a petrol engine, see enclosed instruction
manual on the engine regarding petrol, oil change and maintenance. If
any doubt, contact Briggs & Stratton service personnel.

WARNING: To prevent accidents remove the high tension lead from
the engine before servicing the engine or other parts of the sprayer.

WARNING: REMEMBER SUFFICIENT VENTILATION - NEVER
WORK IN CLOSED ROOMS.
Exhaust gas containing carbon monoxide has no odour but is very
dangerous.

WARNING: NEVER FILL ON PETROL WHEN THE ENGINE IS
WORKING.
Do not spill petrol on a hot engine. This may cause an explosion and
serious injury.

Содержание CT Series





















































Результаты поиска

Содержание CT Series

Отзывы:

Похожие инструкции для CT Series

Бренды по названию

Популярные бренды

Hardi CT Series, Инструкция

Результаты поиска

Содержание CT Series

Отзывы:

Похожие инструкции для CT Series

Бренды по названию

Популярные бренды