manualshive.com logo in svg

Harbor Freight Tools Predator 63966, Руководство пользователя

Поделиться
Скачать
Harbor Freight Tools Predator 63966 Скачать руководство пользователя страница 13

Page 13

For technical questions, please call 1-888-866-5797.

ITEM 63966 
        

S

AFETY

S

ETU

p

Op

ERA

TION

M

AINTENANCE

Connecting Electrical Loads

Familiarize yourself with the engine controls, power panel and how to start the engine before using 
the Generator. Calculate the wattage of the products you will use with the Generator and verify 
that the Generator can handle the total load. 

WARNING!  

Connect only properly wired plugs 

to the Generator.  A plug that is spliced onto a 
different cord may be hazardous.  Only a qualified 
electrician should wire a plug onto a cord. 

NOTICE:  

Never exceed the rated capacity for this Generator, 

as serious damage to the Generator and/or appliances, 
tools, and equipment could result from an overload.  Starting 
and running wattage requirements should always be 
calculated when matching this Generator’s wattage capacity to the appliance, tool, or equipment.

Use the DC12 V Receptacle to power 12 VDC equipment.

 

WARNING! 

Do not charge batteries without a proper charge controller.  Do not overcharge.

a.  Connect the items that require the most wattage first.
b.  Connect “inductive” load appliances, tools, and equipment next.  Inductive 

loads are small hand tools and some small appliances.  

c.  Connect any lights next.
d.  Voltage sensitive appliances, tools, and equipment should be the last to be connected to the Generator.  

Plug voltage sensitive items such as TVs, DVD players, microwaves, and cordless telephones into a  
UL

®

 Listed voltage surge protector (not included).  Then, connect the surge protector into the Generator.

IMpORTANT!

  Failure to connect and operate appliances, tools, and equipment in this sequence can cause 

damage to the Generator, appliances, tools, and equipment and will 

void 

the Warranty of this Generator.

Note:  

If Engine speed or voltage fluctuates with a load below the Generator’s 

running watts, move the Choke Lever to the halfway position.

Evenly distributed 

over outlets:

IF ANY CIRCUIT BREAKERS TRIp CHECK THE FOLLOWING:

1.  Make sure that 

ALL circuit breakers

 are reset 

before starting the Generator again.

2.  Adjust the plugs so the loads are  

shared across outlet circuits.

To achieve rated output from the Generator, 
distribute loads over outlets.

St

1,000

400

200 

 

1,200

Tot

al R

unn

ing

 Wa

tts  

 

 

 

 

4,20

0

Lar

ges

t Ad

diti

ona

l St

art-

up 

Wa

tts

1,200

artu

p Wa

tts 

nee

ded

 for

 all

 loa

ds 

 

 

 

 

5,40

0

Must be 

less than 

5,500

Must be 

less than 

6,500

Содержание Predator 63966





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды