manualshive.com logo in svg
background image

Page 4

For technical questions, please call 1-888-866-5797.

Item 60801 60802 

        

Sa
FE
ty

Op
E

ra
ti

O

n

Maint

E

nanc

E

S

E

tup

air Source

1. 

 

never connect to an air source  

 

that is capable of exceeding  

 

200 psi.

  Over pressurizing the  

 

tool may cause bursting, abnormal  

 

operation, breakage of the tool or 

serious injury to persons.  Use only clean, dry, 
regulated compressed air at the rated pressure 
or within the rated pressure range as marked on 
the tool.  Always verify prior to using the tool that 
the air source has been adjusted to the rated air 
pressure or within the rated air-pressure range.

2. 

Never use oxygen, carbon dioxide, combustible 
gases or any bottled gas as an air source 
for the tool.

  Such gases are capable of 

explosion and serious injury to persons.

 SaVE tHESE inStructiOnS.

SyMBOLS anD SpEciFic SaFEty inStructiOnS

Symbol Definitions

Symbol

property or statement

pSi

Pounds per square inch of pressure

cFM

Cubic Feet per Minute flow

ScFM

Cubic Feet per Minute flow 
at standard conditions

npt

National pipe thread, tapered

npS

National pipe thread, straight

Symbol

property or statement

WARNING marking 
concerning Risk of Eye Injury.  
Wear ANSI-approved eye protection.

WARNING marking concerning Risk of 
Hearing Loss.  Wear hearing protection.

WARNING marking concerning 
Risk of Respiratory Injury.  Wear 
NIOSH-approved dust mask/respirator.

WARNING marking concerning 
Risk of Explosion.

Specific Safety instructions

1.  The warnings and precautions discussed in this 

manual cannot cover all possible conditions and 
situations that may occur.  It must be understood 
by the operator that common sense and caution 
are factors which cannot be built into this 
product, but must be supplied by the operator.

2. 

DO nOt DrOp tanK, riSK OF EXpLOSiOn.

3.  Attach all accessories properly to the Soda Blaster 

before connecting the air supply.  A loose 
accessory may detach or break during operation.

4.  Obey the manual for the air compressor 

used to power this Soda Blaster.

5.  Install an in-line shutoff valve to allow 

immediate control over the air supply in an 
emergency, even if a hose is ruptured.

Содержание CentralPneumatic 60801













Отзывы: