background image

SKU 98279 

For technical questions, please call 1-800-444-3353. 

Page 5

cal Code.  

(See outlets for 2-prong 

plug.)

Double insulated tools may be used 

2. 

in either of the 120 volt outlets shown 

in the preceding illustration.  

(See 

outlets for 2-prong plug.)

extension cords

Grounded

1. 

 tools require a three wire 

extension cord.  

Double Insulated

 

tools can use either a two or three 

wire extension cord.
As the distance from the supply outlet 

2. 

increases, you must use a heavier 

gauge extension cord.  Using exten-

sion cords with inadequately sized 

wire causes a serious drop in voltage, 

resulting in loss of power and pos-

sible tool damage. 

(See table a.)

The smaller the gauge number of the 

3. 

wire, the greater the capacity of the 

cord.  For example, a 14 gauge cord 

can carry a higher current than a 16 

gauge cord.  

(See table a.)

When using more than one exten-

4. 

sion cord to make up the total length, 

make sure each cord contains at 

least the minimum wire size required.  

(See table a.)

If you are using one extension cord 

5. 

for more than one tool, add the 

nameplate

 

amperes and use the sum 

to determine the required minimum 

cord size.  

(See table a.)

If you are using an extension cord 

6. 

outdoors, make sure it is marked with 

the suffix “W-A” (“W” in Canada) to 

indicate it is acceptable for outdoor 

use.

Make sure the extension cord is prop-

7. 

erly wired and in good electrical con-

dition.  Always replace a damaged 

extension cord or have it repaired by 

a qualified electrician before using it.

Protect the extension cords from 

8. 

sharp objects, excessive heat, and 

damp or wet areas.

recommended minimum wire 

gauge For eXtenSion cordS* 

(120/240 Volt)

nameplate

ampereS

(at full load)

eXtenSion cord 

lengtH

25’

50’

75’

100’

150’

0 – 2.0

18

18

18

18

16

2.1 – 3.4

18

18

18

16

14

3.5 – 5.0

18

18

16

14

12

5.1 – 7.0

18

16

14

12

12

7.1 – 12.0

18

14

12

10

-

12.1 – 16.0

14

12

10

-

-

16.1 – 20.0

12

10

-

-

-

taBle a

* Based on limiting the line 

voltage drop to five volts at 

150% of the rated amperes.

Symbology

Double Insulated

Canadian Standards Association

Underwriters Laboratories, Inc.

V~

Volts Alternating Current

a

Amperes

n0 xxxx/min.

No Load Revolutions per Minute 

(RPM)

Содержание 98279








Отзывы: