Page 2
SKU 97146
For technical questions, please call 1-800-444-3353.
The warnings, precautions, and instructions discussed in this instruction manual
10.
cannot cover all possible conditions and situations that may occur. It must be
understood by the operator that common sense and caution are factors which
cannot be built into this product, but must be supplied by the operator.
SAVE THESE INSTRUCTIONS.
SPECIFICATIONS
Batteries
CR2032 3V Lithium Batteries
2 for Transmitter, 1 for each Receiver
(included for each)
Range
~60’ (open distance)
Volume Level
80 dB
UNPACKING
When unpacking, check to make sure that the item is intact and undamaged. If
any parts are missing or broken, please call Harbor Freight Tools at the number shown
on the cover of this manual as soon as possible.
SET UP INSTRUCTIONS
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the
beginning of this manual including all text under subheadings therein
before set up or use of this product.
Note:
For additional information regarding the parts listed in the following pages, refer
to the Assembly Diagram near the end of this manual.
Remove the screw on the battery compartment cover, and observing
1.
polarity, insert two 3V CR2032 Lithium batteries. Screw cover back on.
Note: Positive terminal of batteries on the Transmitter (2) and the Receivers (3)
must be top side.
Mount the Transmitter Base in a central location where the Transmitter will be
2.
easy for adults to access and within the likely range of the Receivers.
Verify that installation surface has no hidden utility lines before drilling or
3.
driving screws.
The distance between the center of the mounting holes is 2-1/8”. Mark holes on the
mounting surface and drive included screws and anchors into mounting surface. At-
tach the Transmitter Base onto the screws, and slide the Transmitter into it.
You may use the connected magnet to apply the Transmitter Base to a metallic
4.
surface (such as a refrigerator).
Unscrew the back covers on the Receivers and, observing polarity, insert
5.
batteries before returning the cover.
Page 3
SKU 97146
For technical questions, please call 1-800-444-3353.
OPERATING INSTRUCTIONS
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the
beginning of this manual including all text under subheadings therein
before set up or use of this product.
Using the safety clip at the end of the swiveling link chain attach the Receivers
1.
to items that can be hard to find (keys or remote controls). Turn the switch on
the side of the Receiver on.
Turn on the switch on the back of the Transmitter. When the Transmitter is
2.
removed from its mounting, it will beep every two minutes unless the sound
is turned off. The Buttons on the Transmitter are color-coded to match the
Receivers. To locate the item, push the button (Button 1 or 2) that corresponds
to the color of the Receiver clipped to the item, then push the “F” Key.
The Receiver will beep and the light will flash until the matching button is
3.
pressed again.
The range of the Transmitter is about 60 Feet. The presence of walls or strong
4.
transmitting sources can disrupt the signal. It may be necessary to walk around
obstacles and push the button a few more times for the signal to reach the
Receiver.
Push the button on the Transmitter to turn off the Receiver before you retrieve
5.
the item.
If the Transmitter can not find the Receiver: press the Learn button until it beeps
6.
twice, enter a new code on the Transmitter and then push the Finding button.
The Receiver will either issue one long beep to indicate a successful change or
beep repeatedly to indicate failure. In case of failure, try again.
Three more Receivers may be available for use with this Transmitter. Check
7.
with your local Harbor Freight Tools store or call the number below for details.
Return the Transmitter to the Transmitter Base, then store the Transmitter and
8.
Receivers out of children’s reach.
MAINTENANCE AND SERVICING
Before each use, inspect the general condition of the product. Check for loose
1.
screws, stuck buttons, cracked or broken parts, and any other condition that
may affect its safe operation.
After use, clean external surfaces of the tool with clean, moist cloth.
2.
Batteries
3.
. When batteries must be replaced, remove the back cover of the unit
and, paying attention to polarity, add new 3V Lithium CR2032 Batteries. Each
Receiver requires its own battery. The Transmitter requires 2 Batteries, do not
install batteries of different types, charge levels, or capacities together.
Dispose
of Lithium batteries at a local Hazardous Waste Disposal site only
.
