Harbor Freight Tools 67596 Скачать руководство пользователя страница 7

Страница: 7 / 28

Page 7

For Pressure Washer technical questions, please call 1-800-444-3353.

SKU 67546/67596

For engine technical questions, please call 1-800-520-0882.

Set up instructions

Read the entiRe imPORtant

SaFetY inFORmatiOn section at the

beginning of this manual including

all text under subheadings therein

before set up or use of this product.

Risk of accidental starting;

resulting in serious personal

injury. turn the Power

Switch of the equipment to its “OFF” position, wait

for the engine to cool, and unplug the spark plug

wire(s) before assembling or making any adjustments

to the equipment.

note:

For additional information regarding the parts

listed in the following pages, refer to the

Assembly Diagram near the end of this manual.

assembly

Operation of this equipment may create sparks

that can start fires around dry vegetation. A spark

arrestor may be required. The operator should

contact local fire agencies for laws or regulations

relating to fire prevention requirements.

Brass Pump

Plug (14A)

Aluminum Pump

Breather Plug

(59A)

Dipstick (60A)

Figure 1

Replace the Brass Pump Plug (14A) with the

aluminum Pump Breather Plug (59A) and Dipstick

(60A) before first use. The Pump Breather Plug

must be used whenever the pressure washer is

used. The Brass Pump Plug (without the breather

hole) should be used for transporting only.

Attach the Handle (14) onto the Frame (17)

with the Handle Bolts (15) and Nuts (16).

Outlet

Connector

(35A)

Water Inlet

Connection

Detergent Inlet

Connection

(26A)

Pressure Regulator Knob (44A)

Figure 2

Attach the Hose (18) to the Outlet Connector

(35A) on the unit (See Figure 2).

Pull the Collar at the end of the hose back

and attach the Gun (19) to the hose.

Screw the Wand (20) onto the Gun (19)

and secure with the grommet.

Choose the right Nozzle (5) for the job. Pull back

the quick connect collar and push the Nozzle

onto the end of the Wand. Make sure the quick

connect collar locks the Nozzle in place.

• Black

Nozzle -

low Pressure

Used with pressure washer detergent.

• White

Nozzle -

Wide Spray

Used to clean very large areas.

• Green

Nozzle -

medium Spray

Used to clean larger areas.

• Yellow

Nozzle -

narrow Spray

Used to clean small areas.

• Red

Nozzle -

Pencil Spray

Only use on hard surfaces such as

concrete or metal. Can damage wood.

Connect the water supply to the Water Inlet

Connection on the Water Inlet Body (42A). The

water source must be able to provide a minimum

of five gallons of clean, cold water per minute

at 20 PSI. Only use a 5/8” inner diameter (or

larger) hose that is rated to meet this capacity.

if using detergent:

Read detergent directions. Connect one

end of the Detergent Inlet Hose (8) to the

Detergent Inlet Connection, and the other

end into the container holding the detergent.

Only use detergents specified for use with

Pressure Washers. The Pressure Washer will

draw one gallon of detergent for every seven

gallons of water. Only use the Black (low

pressure) Nozzle when spraying detergents.

WaRninG

Rev 11c

Содержание 67596





























Результаты поиска

Содержание 67596

Отзывы:

Бренды по названию

Популярные бренды

Harbor Freight Tools 67596, Руководство пользователя

Результаты поиска

Содержание 67596

Отзывы:

Бренды по названию

Популярные бренды