background image

ASSEMBLY INSTRUCTIONS

1

3

5

7b

9

8

1. 

Turn off circuit breakers and wall switch to 

the fan supply line leads. 

DANGER:

 Failure to disconnect the 

power supply prior to installation may 

result in serious injury or death.

2. With the mounting bracket (B) resting 

inside the canopy (C), partially install two 

mounting bracket screws (EE) into the 

two holes surrounded by the J-slots in the 

canopy (C). Then, remove the mounting 

bracket (B) from the canopy (C).  

3. Using the screws and washers provided 

with the outlet box (not included), secure 

the mounting bracket (B) to a “Ceiling 

Fan Rated” outlet box. The opening of 

mounting bracket (B) should open toward 

the floor.

4. Slide the accessory downrod (sold 

separately) into the yoke of the ceiling fan. 

Install the accessory downrod according 

to the instruction manual included with the 

ceiling fan.

5. If using this item on an angled ceiling,

 

snap out the perforated section of the 

canopy cover (D).

6. Slide the canopy (C) of your choice and 

the ball (A) onto the accessory downrod. 

Note:

 Ball (A) must be positioned with the 

holes near the top of the downrod. 

2

B

B

C

B

EE

A

A

A

DD

D

A

C

CC

BB

BB

DD

CC

AA

E

10

6

7a

Printed in China

7a. If using a 3/4-inch diameter 

accessory downrod, 

attach the ground 

wire (CC) to the smaller hole in the 

accessory downrod using the ground 

screw (BB). Then slide the pin (DD) 

into the two large holes at the top of the 

downrod.

7b. 

If using a 1/2-in. diameter downrod, 

slide the ball adapter (E) onto the 

accessory downrod and down into the 

center of the ball (A). Then, attach the 

ground wire (CC) to the small hole in 

the top of the accessory downrod with 

the ground screw (BB). Align the large 

holes in the ball adapter (E) with the 

large holes in the top of the accessory 

downrod, then slide pin (DD) through 

larger holes in the ball adapter (E) and 

downrod. 

8. Raise the ball (A) to the top of accessory 

downrod, aligning hole in the ball (A) 

with set screw hole at top of downrod. 

This will allow the pin (DD) to fall into 

the proper slot in the top of the ball (A). 

Then, secure the ball (A) to the top of 

the accessory downrod using the set 

screw (AA). 

9. Lift the ball (A) along with the fan into 

the opening in the mounting bracket (B). 

Align one of the slots in the ball (A) with 

tab in the mounting bracket (B). 

DANGER:

 Failure to align a slot in 

the ball (A) with the tab in the mounting 

bracket (B) may cause fan to wobble or 

fall, which could result in serious injury 

or death.

10. Align the canopy (C) over the 

loose mounting bracket screws (EE) 

preassembled on the mounting bracket 

(B) in Step 2. Then, twist canopy (C) to 

lock. Insert two more mounting bracket 

screws (EE) into the round holes of the 

canopy (C). Tighten all four mounting 

bracket screws (EE).

Opening

Accessory 

Downrod

Yoke

Tab

Slot

Note: 

This item was designed for use with an existing ceiling fan.  It will be necessary to purchase a longer downrod in order to install the fan to a vaulted ceiling. 

The parts included with this item will be used instead of similar parts included with your fan. 

 

4

Hole

9168 • 101716

B

EE

C

2

Top view

J-slot

DD

Hole

Отзывы: