▍Time setting
▍Program setting
▍Control method for temperature
█ Key operation function description
[2.tyP]
“PL.2”: 1, 2nd stage setting and 1, 2nd stage control (control 2nd stage priority)
"PL.1" : 1st stage setup and 1st stage control only.
[CLOSE Output Relay]
•Closed 1 operation
If the current temperature is lower than the set temperature (CLo.1), the CLOSE output relay is operated,
and the output relay is “ON / OFF” according to the ON/OFF time (CL1.n / CL1.F) of the close 1 operation.
[CLOSE Output Relay ]
•Close 2 operation (However, the operation priority is higher than the closed 2 action.)
If the current temperature is lower than the set temperature (CLo.1 + CLo2), the CLOSE output relay operates.
The output relay turns "ON / OFF" according to the ON/OFF time (CL2.n/CL2.F) of the closed 2 operation.
[OPEN Output Relay]
● 2.tyP = PL.2(Stage 2 control operation)
• Open 2 operation (However, the operation priority is higher than Open 2 operation.)
If the current temperature is higher than the set temperature (oPE.1 + oPE.2), the OPEN output relay operates.
The output relay is "ON / OFF" according to the ON / OFF time (oP2.n / oP2.F) of open 2 operation.
● 2.tyP = PL.1(Stage 1 control operation)
•Open 1 operation
When the current temperature is higher than the set temperature (OPE.1), the OPEN output relay is operated.
The output relay is "ON/OFF" according to the ON/OFF time (oP1.n/oP1.F) setting of Open1 operation.
[OPEN Output Relay]
·Operation: oPE.1 output ON time
·Setting value change( , ) : 1 ~ 999
·Operation: CLo.1 output ON time
·Setting value change( , ) : 1 ~ 999
·Operation: CLo.1 output ON time and OFF time
·Setting value change( , ) : 1 ~ 999
·Operation: oPE.2 output ON time
·Setting value change( , ) : 1 ~ 999
Default : 10(Sec)
·Operation: OFF time after output ON time of oPE.2
·Setting value change( , ) : 1 ~ 999
Default : (1 Min)
·Operation: CLo.2 output ON time
·Setting value change( , ) : 1 ~ 999
Default : (10 Sec)
Operation: CLo.2 output ON time and OFF time
·Setting value change( , ) : 1 ~ 999
Default : (1 Min)
·Operation: OFF time after output ON time of oPE.1
·Setting value change( , ) : 1 ~ 999
Default : oFF
Default : PL.1
Default : 0℃
Default : 5.0℃
Default : sec
Default : Min
Default
(10 Sec)
Default
(10 Sec)
Default
(1 Min)
Default
(1 Min)
온도설정
시간설정
프로그램설정
Open 1 operation ON time
Open 1 operation OFF time
Closing 1 operation ON time
Closing 1 operation OFF time
Open 2 operation ON time
Open 2 operation OFF time
Closed 2 operation ON time
Closed 2 operation OFF time
Save time setting value
※ Press for more than 3 seconds.
(Enter the mode or save the set value)
on (lock): locks all set values in program setting mode
oFF (Release): Unlock all set values in program setting mode
Setting data lock function
·“PL.2”: 1st and 2nd stage setting and 1st and 2nd stage control (control 2nd stage priority)
·“PL.1”: 1st stage setting and 1st stage control only
Control method selection (1st stage control operation or 2nd stage control operation)
·Temperature compensation for sensor line length or error occurrence (-10.0 ~ 10.0 ℃)
Measurement value correction setting
·Constant deviation is required during ON/OFF operation (0.1 ~ 25.0 ℃)
Hysteresis
Sec: Seconds (display lamp m: OFF)
Min: minute unit (display lamp m: ON)
Select output ON time unit
Sec: Seconds (display lamp m: OFF)
Min: minute unit (display lamp m: ON)
Select output OFF time unit
Current
temperature
Current
temperature
Default :
30.0 ℃
Default :
10.0 ℃
Default :
10.0 ℃
Default :
-10.0 ℃
Save
temperature
setting value
※
In the program setting mode, “2. Displayed only when tyP = PL.2” is set.
※
※ When setting “2.tyP = PL.2” in program setting mode
The priority of the task is "2 tasks (2 open, 2 closed)".
Open 1 operation temperature setting
(Set temperature (oPE.1) <present temperature (PV))
·Operation: Operates when the current temperature is higher than
the set temperature (oPE.1)
·Setting value change( , ) : -40.0 ~ 90.0 ℃
(Set temperature (CLo.1) <present temperature (PV))
Closed 1 operating temperature setting
·Operation: Operates when the current temperature is lower
than the set temperature (CLo.1)
·Setting value change( , ) : -40.0 ~ 90.0 ℃
Open 2 operation temperature setting
(Set temperature (oPE.1+oPE.2) <present temperature (PV))
·Operation: Operates when the current temperature is higher than
the set temperature (oPE.1 + oPE2)
·Setting value change( , ) : 1.0 ~ 130.0 ℃
Closed 2 operating temperature setting
(Set temperature (CLo.1 + CLo.2)> Current temperature (PV))
·Operation: Operates when the current temperature is lower than
the set temperature (CLo.1 + CLo.2)
·Setting value change( , ) : -1.0 ~ -99.0 ℃
Current
temperature
Current
temperature
Current
temperature
※
Displayed only when “2.tyP=PL.2”
is set in the program setting mode.
※
·Operation: oPE.1 output ON time
·Setting value change( , ) : 1 ~ 999
·Operation: CLo.1 output ON time
·Setting value change( , ) : 1 ~ 999
·Operation: CLo.1 output ON time and OFF time
·Setting value change( , ) : 1 ~ 999
·Operation: oPE.2 output ON time
·Setting value change( , ) : 1 ~ 999
Default : 10(Sec)
·Operation: OFF time after output ON time of oPE.2
·Setting value change( , ) : 1 ~ 999
Default : (1 Min)
·Operation: CLo.2 output ON time
·Setting value change( , ) : 1 ~ 999
Default : (10 Sec)
Operation: CLo.2 output ON time and OFF time
·Setting value change( , ) : 1 ~ 999
Default : (1 Min)
·Operation: OFF time after output ON time of oPE.1
·Setting value change( , ) : 1 ~ 999
Default : oFF
Default : PL.1
Default : 0℃
Default : 5.0℃
Default : sec
Default : Min
Default
(10 Sec)
Default
(10 Sec)
Default
(1 Min)
Default
(1 Min)
온도설정
시간설정
프로그램설정
Open 1 operation ON time
Open 1 operation OFF time
Closing 1 operation ON time
Closing 1 operation OFF time
Open 2 operation ON time
Open 2 operation OFF time
Closed 2 operation ON time
Closed 2 operation OFF time
Save time setting value
※ Press for more than 3 seconds.
(Enter the mode or save the set value)
on (lock): locks all set values in program setting mode
oFF (Release): Unlock all set values in program setting mode
Setting data lock function
·“PL.2”: 1st and 2nd stage setting and 1st and 2nd stage control (control 2nd stage priority)
·“PL.1”: 1st stage setting and 1st stage control only
Control method selection (1st stage control operation or 2nd stage control operation)
·Temperature compensation for sensor line length or error occurrence (-10.0 ~ 10.0 ℃)
Measurement value correction setting
·Constant deviation is required during ON/OFF operation (0.1 ~ 25.0 ℃)
Hysteresis
Sec: Seconds (display lamp m: OFF)
Min: minute unit (display lamp m: ON)
Select output ON time unit
Sec: Seconds (display lamp m: OFF)
Min: minute unit (display lamp m: ON)
Select output OFF time unit
Current
temperature
Current
temperature
Default :
30.0 ℃
Default :
10.0 ℃
Default :
10.0 ℃
Default :
-10.0 ℃
Save
temperature
setting value
※
In the program setting mode, “2. Displayed only when tyP = PL.2” is set.
※
※ When setting “2.tyP = PL.2” in program setting mode
The priority of the task is "2 tasks (2 open, 2 closed)".
Open 1 operation temperature setting
(Set temperature (oPE.1) <present temperature (PV))
·Operation: Operates when the current temperature is higher than
the set temperature (oPE.1)
·Setting value change( , ) : -40.0 ~ 90.0 ℃
(Set temperature (CLo.1) <present temperature (PV))
Closed 1 operating temperature setting
·Operation: Operates when the current temperature is lower
than the set temperature (CLo.1)
·Setting value change( , ) : -40.0 ~ 90.0 ℃
Open 2 operation temperature setting
(Set temperature (oPE.1+oPE.2) <present temperature (PV))
·Operation: Operates when the current temperature is higher than
the set temperature (oPE.1 + oPE2)
·Setting value change( , ) : 1.0 ~ 130.0 ℃
Closed 2 operating temperature setting
(Set temperature (CLo.1 + CLo.2)> Current temperature (PV))
·Operation: Operates when the current temperature is lower than
the set temperature (CLo.1 + CLo.2)
·Setting value change( , ) : -1.0 ~ -99.0 ℃
Current
temperature
Current
temperature
Current
temperature
※
Displayed only when “2.tyP=PL.2”
is set in the program setting mode.
※
·Operation: oPE.1 output ON time
·Setting value change( , ) : 1 ~ 999
·Operation: CLo.1 output ON time
·Setting value change( , ) : 1 ~ 999
·Operation: CLo.1 output ON time and OFF time
·Setting value change( , ) : 1 ~ 999
·Operation: oPE.2 output ON time
·Setting value change( , ) : 1 ~ 999
Default : 10(Sec)
·Operation: OFF time after output ON time of oPE.2
·Setting value change( , ) : 1 ~ 999
Default : (1 Min)
·Operation: CLo.2 output ON time
·Setting value change( , ) : 1 ~ 999
Default : (10 Sec)
Operation: CLo.2 output ON time and OFF time
·Setting value change( , ) : 1 ~ 999
Default : (1 Min)
·Operation: OFF time after output ON time of oPE.1
·Setting value change( , ) : 1 ~ 999
Default : oFF
Default : PL.1
Default : 0℃
Default : 5.0℃
Default : sec
Default : Min
Default
(10 Sec)
Default
(10 Sec)
Default
(1 Min)
Default
(1 Min)
온도설정
시간설정
프로그램설정
Open 1 operation ON time
Open 1 operation OFF time
Closing 1 operation ON time
Closing 1 operation OFF time
Open 2 operation ON time
Open 2 operation OFF time
Closed 2 operation ON time
Closed 2 operation OFF time
Save time setting value
※ Press for more than 3 seconds.
(Enter the mode or save the set value)
on (lock): locks all set values in program setting mode
oFF (Release): Unlock all set values in program setting mode
Setting data lock function
·“PL.2”: 1st and 2nd stage setting and 1st and 2nd stage control (control 2nd stage priority)
·“PL.1”: 1st stage setting and 1st stage control only
Control method selection (1st stage control operation or 2nd stage control operation)
·Temperature compensation for sensor line length or error occurrence (-10.0 ~ 10.0 ℃)
Measurement value correction setting
·Constant deviation is required during ON/OFF operation (0.1 ~ 25.0 ℃)
Hysteresis
Sec: Seconds (display lamp m: OFF)
Min: minute unit (display lamp m: ON)
Select output ON time unit
Sec: Seconds (display lamp m: OFF)
Min: minute unit (display lamp m: ON)
Select output OFF time unit
Current
temperature
Current
temperature
Default :
30.0 ℃
Default :
10.0 ℃
Default :
10.0 ℃
Default :
-10.0 ℃
Save
temperature
setting value
※
In the program setting mode, “2. Displayed only when tyP = PL.2” is set.
※
※ When setting “2.tyP = PL.2” in program setting mode
The priority of the task is "2 tasks (2 open, 2 closed)".
Open 1 operation temperature setting
(Set temperature (oPE.1) <present temperature (PV))
·Operation: Operates when the current temperature is higher than
the set temperature (oPE.1)
·Setting value change( , ) : -40.0 ~ 90.0 ℃
(Set temperature (CLo.1) <present temperature (PV))
Closed 1 operating temperature setting
·Operation: Operates when the current temperature is lower
than the set temperature (CLo.1)
·Setting value change( , ) : -40.0 ~ 90.0 ℃
Open 2 operation temperature setting
(Set temperature (oPE.1+oPE.2) <present temperature (PV))
·Operation: Operates when the current temperature is higher than
the set temperature (oPE.1 + oPE2)
·Setting value change( , ) : 1.0 ~ 130.0 ℃
Closed 2 operating temperature setting
(Set temperature (CLo.1 + CLo.2)> Current temperature (PV))
·Operation: Operates when the current temperature is lower than
the set temperature (CLo.1 + CLo.2)
·Setting value change( , ) : -1.0 ~ -99.0 ℃
Current
temperature
Current
temperature
Current
temperature
※
Displayed only when “2.tyP=PL.2”
is set in the program setting mode.
※
▍Temperature setting